|
12 bolt rear
(Preview)
I need to know the width (backing plate) to same of a late 60's full size GM. My 50 Pontiac is about 54/55" width and I'm thinking of using one of these differentials for my build.
|
forespeed
|
2
|
876
|
|
|
|
How to decode engine #
(Preview)
Hi, I have a 1965 Parisienne Convertible which lost its original engine at some point along the way. The owners manual lists the original engine #805504170. Does anyone know how to determine from this code what the original engine was that came in the car? Thanks.
|
Rael Fisher
|
11
|
1110
|
|
|
|
Compatible Differentials for 1967 Parisienne Convertible
(Preview)
What vehicles would have a compatible differential with a 327 1967 Parisienne? Would a 1964 differential work? Would the 64 fuel tank also swap over? let me know!
|
flatland67
|
7
|
885
|
|
|
|
B body 12 bolt, conversion to posi, any thoughts on gear suppliers?
(Preview)
I'm getting ready to completely rebuild the Gp's rear suspension. And while the standard 12 bolt diff is out, I'm going to add Posi. Any thoughts on a good gear supplier before I click buy? The one that's sitting in the cart is a Richmond 3.55 set. I'm also going with an Eaton Posi unit and Moser axles. A...
|
cdnpont
|
7
|
1023
|
|
|
|
Set up 12 bolt
(Preview)
Does anyone know of someone that can set up and or repair a 12 bolt, in or near the Calgary vicinity? That is, for a reasonable price, not $1000's.
|
1965CS
|
2
|
794
|
|
|
|
307 Engine for 68 Beaumont, original, as is , running condition.
(Preview)
Can anyone tell me what I can expect to pay for a 68 Beaumont 307 engine in "as is" running condition.
|
Roy
|
2
|
527
|
|
|
|
engine cooling
(Preview)
Hi Guys I would like to upgrade the fan on my 67 parisienne It has 4 blades direct drive I was thinking of installing a clutch fan and blade does anyone have advice as to what parts to order? things are a little tight as far as clearances go (top rad hose)(space between rad and mounting base of short water pu...
|
SGS Welding
|
9
|
884
|
|
|
|
|
65 Pontiac Parisienne Convertable
(Preview)
Hello all, I am in possession of a 65 Pontiac Parisienne Convertable and was wondering if maybe someone could help me find the VIN plate. I looked in the common area, where the window meets the dash but no luck. I found the serial number and it is a Canadian made car but would like to know more about it as...
|
Rmedave
|
14
|
1284
|
|
|
|
Big block radiator with a small block engine.
(Preview)
Recently my radiator came loose from the mounting brace when driving over a pot hole and moved close to my fan and got a nice clear cut right through it, not it's no good. There is someone locally who has a big block radiator, so my question is, will it fit? I have a 1966 Pontiac Beaumont -- Edited by blackb...
|
blackbird307
|
13
|
1664
|
|
|
|
Cooling upgrade
(Preview)
Hi guys I was wondering if there is a nice simple kit I could purchase that fits well,has all the hardware included.
Just to specify I am talking about an electric fan that fits over the radiator.
|
SGS Welding
|
5
|
575
|
|
|
|
Magnet included in my 12 bolt shim kit. Where should it go?
(Preview)
I bought a 12 bolt 8.875" Super shim and Solid pinion spacer kit from a shop in BC. It came with a magnet, and I'm wondering if I should use it, and if I do, where should it go? Is it something that should always be done? My cover is aluminum, so without epoxy, it won't sit there.
|
cdnpont
|
4
|
877
|
|
|
|
Installed spacer for fan shroud
(Preview)
Hi Yesterday I took the Impala to Exeltech Auto in Markham. They recentlyl put in the 350 crate engine for me. I had purchased a 3.00 inch fan spacer to get the fan further into the shroud as I wasn't happy with the temp guage and others on here had posted much cooler temps. The fan spacer was designed i...
|
oshawacliff
|
10
|
1096
|
|
|
|
carb suggestions
(
1 2
)
(Preview)
I was wondering what is a good carb to put on a 67 parisienne ? 4 barrel intake 327 2 speed powerful glide not sure about the choke setup?does it have to be the same as whats there now? it is a q-jet on right now it runs ok but fouls plugs and uses a lot of fuel leaves black stains everywhere out the tailpipes on t...
|
SGS Welding
|
49
|
2150
|
|
|
|
Hei conversion
(Preview)
I have a 1980 1 ton tow truck 350 standered in my TREASURE collection behind the house If I simply install this hei into my parisienne how far off would I be with the ignition curve? It looks like it has heavy springs and weights and the vacuum has a 10 stamped on it My thinking is they both have 350 4 barrels...
|
SGS Welding
|
2
|
550
|
|
|
|
|
3/8", 0-30 inch pound dial indicator torque wrench wanted.
(Preview)
Guys, I'm looking for a 3/8", 0-30 in/lb dial indicator torque wrench. It's really the only way to determine an accurate pinion preload. There is really nothing on ebay right now, so I've come here. If anyone knows of one for sale, any leads, could you please let me know. I'd even rent it from a me...
|
cdnpont
|
6
|
733
|
|
|
|
Different speedo gear ratios for the TH400?
(Preview)
To correct my speedo drive on the TH400 to my new upcoming ratio of 3.55, what would that involve? Are different gears still available? Can they be supplied through GM? How much work is involved to change it? Any info appreciated, Thanks, Mark
|
cdnpont
|
7
|
1172
|
|
|
|
Fuel gauge quit :(
(Preview)
Hey guys, My fuel gauge quit yesterday after filling up. The gauge rose to full, and at the next start up after shutdown I noticed it at empty. The tank and sender were both new 4 years ago. No problem until now. One thing I did notice while filling, was I thought I heard a few strange clicking sounds comi...
|
cdnpont
|
8
|
673
|
|
|
|
Fuel line for big block with Q-Jet
(Preview)
I have looked for a steel fuel line, to run from fuel pump to intake of 396/427 engines with Q-Jet They are available from Jegs,Summit and Impala Bobs and more it lists the package as 2 pieces and shows pictures of 2 full size lines 1. Anyone know why? Q-jet has filter in carb 2. I have seen posi...
|
427carl
|
22
|
1033
|
|
|
|
no part throttle shift for 2 speed powerfulglide
(Preview)
hi guys looking for more help car is a 1967 pontiac parisienne cv 327 2speed auto 12 bolt (actually a 350 now someone changed it along the way)(still has originnal carb and intake) the only way to get into 2nd gear (or final drive) is to run the car up to 50+ mph then get my shift after that i can cruise as low a...
|
SGS Welding
|
22
|
910
|
|
|
|
Alternator replacement
(Preview)
Hey guys, The charging system on my '66 Strato Chief stopped working. I changed battery cables, cleaned grounds and charged/tested battery. Only thing left is the alternator and regulator. I think I'm just going to buy a new alternator. But I would like to buy one with an internal regulator. Do you g...
|
Razzmyth
|
18
|
1625
|
|
|