Clint, what's the spacing between holes? I just may have spacers.
seventy2plus2 said
Dec 4, 2014
Greaser wrote:
Clint, what's the spacing between holes? I just may have spacers.
About 7/8" on both pieces.
Greaser said
Dec 4, 2014
seventy2plus2 wrote:
Greaser wrote:
Clint, what's the spacing between holes? I just may have spacers.
About 7/8" on both pieces.
I think the ones I have are spaced more like 1-1/2 inches.
koolconvertible said
Dec 4, 2014
Guys, let me say you are all truly awsome in here! Offering to help me even if I am on the other side of the planet! I do have a set which are in so so condition but with a bit of effort will clean up ok. I was hoping they were available new. I really appreciate your help! If you need anything sent over from Australia, let me know, like some yummy vegemite for your breakfast toast! Thanks heaps!
koolconvertible said
Dec 4, 2014
and I might add this is pontiac heaven if ever I've seen it! ai drool over some of the ponchos in here!
seventy2plus2 said
Dec 4, 2014
I don't think reproductions are available as I haven't seen anything. Finding the right screws is often the challenge.
Greaser said
Dec 4, 2014
seventy2plus2 wrote:
I don't think reproductions are available as I haven't seen anything. Finding the right screws is often the challenge.
Spotted this on ebay.....looks a bit different than what's required.........
E Bay 65-69 GM Models Door Alignment Rub Striker Plate Wedges - SET Made in the USA
Those are maybe for A body (mid-size) cars, but not for B body (full size) cars.
koolconvertible said
Dec 4, 2014
I bought mine from USebay before I found discovered canadian poncho. paid good money for them too. I bought a replacement convertible roof with a glass rear window, then found a chev body manual which detailed roof installation. Discovered two special lowering rods which attach to the back seat panel were required so the glass drops,lifts and sits correctly when up. Very hard to find in australia....went to a swap meet and got talking to a fella with a 66 convertible who replaced his roof with a plastic zipout rear window. He happened to have the rods. Swapped some superb quality 66 grill surrounds for them. Good score!
does anyone repro the small convertible door jam rub plates and strike plates?
picture please; My Aussie is not up to speed as yet
Dale @ NOS a poncho supporter
I should have a set in the garage, just not sure if they're correct for your 65 - but they should be. I'll see if I can post a photo tomorrow.
door anti rattle plates?
I'm sure I have them, just not with the spacer. Will post a photo later today.
Here's a set complete with the proper screws. Just clean 'em up and install.
Clint, what's the spacing between holes? I just may have spacers.
About 7/8" on both pieces.
I think the ones I have are spaced more like 1-1/2 inches.
and I might add this is pontiac heaven if ever I've seen it! ai drool over some of the ponchos in here!
I don't think reproductions are available as I haven't seen anything. Finding the right screws is often the challenge.
Spotted this on ebay.....looks a bit different than what's required.........
E Bay 65-69 GM Models Door Alignment Rub Striker Plate Wedges - SET Made in the USA
http://www.ebay.com/itm/65-69-GM-Models-Door-Alignment-Rub-Striker-Plate-Wedges-SET-Made-USA-/390764460452?pt=Motors_Car_Truck_Parts_Accessories&vxp=mtr&hash=item5afb6079a4
Those are maybe for A body (mid-size) cars, but not for B body (full size) cars.