I purchased a sway bar kit from OPGI. I installed the front no problem. The rear, 10 bolt 3.73 posi, never had a sway bar but I want to add it. Has anyone done this that could post a picture of how it will mount? It came with bolts and spacers, shims and what I believe are pieces to box in the tailing arms....but NO instructions.
Any help would be appreciated
Carguy17
dualquadpete said
Apr 6, 2015
check your trailing arms for any holes!!!! I did one on a 69 olds cutlass & there was only 1 hole in the arm, installed the bar with 1 bolt,& a clamp, drilled 2nd. hole, then added the spacers inside the trailing arm[so in doesn't crush when tightening the bolts] Easy peasy
OK that's a horse of a different colour!!! Never seen that set up!!!!
Carguy17 said
Apr 6, 2015
Yes that is part of the kit and it includes the bolts and spacers to keep from crushing the arms. I will be installing this in a few days, I'll post pics.
Carguy17 said
Apr 15, 2015
Hi Guys, I got the sway bar mounted! I elected not to use the piece to box in the arms it seemed like a needless step when it does nothing to improve performance and doesn't totally box in the trailing arm. Thanks for your responses they were helpful. Can't wait to get this car on the road!
That piece is there for a reason. Likely you will crack one or both of your control arms before too long. They just can't take the twisting action that occurs as you corner. Experience talking here! :)
koolconvertible said
Apr 15, 2015
StriperSS wrote:
That piece is there for a reason. Likely you will crack one or both of your control arms before too long. They just can't take the twisting action that occurs as you corner. Experience talking here! :)
x2, they need to be boxed.
Pontiacanada said
Apr 16, 2015
koolconvertible wrote:
StriperSS wrote:
That piece is there for a reason. Likely you will crack one or both of your control arms before too long. They just can't take the twisting action that occurs as you corner. Experience talking here! :)
x2, they need to be boxed.
x3 Yup.
Carguy17 said
Apr 16, 2015
Well that is something I hadn't considered, guess I'll be boxing them in today...it never ends...but that's okay. Thanks again.
bjburnout said
Oct 31, 2015
.........this may help......article from 65 66 Full Size Chev Club
I think he was working on an A body (69 Beaumont?), but not sure.
bjburnout said
Oct 31, 2015
seventy2plus2 wrote:
I think he was working on an A body (69 Beaumont?), but not sure.
.......the pics are from a 66 Impala.......
4SPEED427 said
Oct 31, 2015
Same bar on both cars though, so the mounting stuff should be the same.
Carguy17 said
Oct 31, 2015
Hi guys, As I stated earlier I did get the sway bar mounted. I elected not to box it for now and used the spacers. I did get the car on the road about a month and a half ago and have been enjoying every minute that I get to drive her! I am making a list of items that I want to tweak as I move forward on the list is a set of boxed lower trailing arms.
Same bar on both cars though, so the mounting stuff should be the same.
Basically an A body sway bar is used on B Body cars, and there are spacers required to do that as the control arms are wider apart on the B body cars. Also the way the bar bolts to the control arms is different between A body & B body cars. I believe the spacers Carguy17 is talking about is to go in the control arms so they don't crush.
4SPEED427 said
Oct 31, 2015
seventy2plus2 wrote:
Carl Stevenson wrote:
Same bar on both cars though, so the mounting stuff should be the same.
Basically an A body sway bar is used on B Body cars, and there are spacers required to do that as the control arms are wider apart on the B body cars. Also the way the bar bolts to the control arms is different between A body & B body cars. I believe the spacers Carguy17 is talking about is to go in the control arms so they don't crush.
Again I learn, sigh......!
I have pulled bars off A and B cars over the years and never noticed anything different. I thought they both just had two horizontal bolts through a strengthened control arm. What did I miss?
seventy2plus2 said
Oct 31, 2015
Carl Stevenson wrote:
seventy2plus2 wrote:
Carl Stevenson wrote:
Same bar on both cars though, so the mounting stuff should be the same.
Basically an A body sway bar is used on B Body cars, and there are spacers required to do that as the control arms are wider apart on the B body cars. Also the way the bar bolts to the control arms is different between A body & B body cars. I believe the spacers Carguy17 is talking about is to go in the control arms so they don't crush.
Again I learn, sigh......!
I have pulled bars off A and B cars over the years and never noticed anything different. I thought they both just had two horizontal bolts through a strengthened control arm. What did I miss?
In the middle photo of the 66 Impala above (looking rearward along the lower control arm) you can see 2 different spacers between the sway bar and the control arm. The spacer closest to the sway bar can either be square or round, and there is two of them (one on each bolt). The spacer closest to the control arm is a rectangular plate that covers both bolts. The rear bolt goes all the way through the control arm, and requires a spacer within the control arm so it doesn't crush, but the front bolt only goes into the middle of the control arm. I have the sheet from the GM assembly manual that gives the dimensions and how they bolt together.
bjburnout said
Oct 31, 2015
...that GM spec sheet seventy2plus2 mentions is also in this link........
I purchased a sway bar kit from OPGI. I installed the front no problem. The rear, 10 bolt 3.73 posi, never had a sway bar but I want to add it. Has anyone done this that could post a picture of how it will mount? It came with bolts and spacers, shims and what I believe are pieces to box in the tailing arms....but NO instructions.
Any help would be appreciated
Carguy17
www.opgi.com/chevelle/RCAI001/
They need to be welded in...
Hi Guys, I got the sway bar mounted! I elected not to use the piece to box in the arms it seemed like a needless step when it does nothing to improve performance and doesn't totally box in the trailing arm. Thanks for your responses they were helpful. Can't wait to get this car on the road!
x2, they need to be boxed.
x3 Yup.
.........this may help......article from 65 66 Full Size Chev Club
http://66impalass427.tripod.com/id14.html
I think he was working on an A body (69 Beaumont?), but not sure.
.......the pics are from a 66 Impala.......
Hi guys, As I stated earlier I did get the sway bar mounted. I elected not to box it for now and used the spacers. I did get the car on the road about a month and a half ago and have been enjoying every minute that I get to drive her! I am making a list of items that I want to tweak as I move forward on the list is a set of boxed lower trailing arms.
Cameron
Basically an A body sway bar is used on B Body cars, and there are spacers required to do that as the control arms are wider apart on the B body cars. Also the way the bar bolts to the control arms is different between A body & B body cars. I believe the spacers Carguy17 is talking about is to go in the control arms so they don't crush.
Again I learn, sigh......!
I have pulled bars off A and B cars over the years and never noticed anything different. I thought they both just had two horizontal bolts through a strengthened control arm. What did I miss?
In the middle photo of the 66 Impala above (looking rearward along the lower control arm) you can see 2 different spacers between the sway bar and the control arm. The spacer closest to the sway bar can either be square or round, and there is two of them (one on each bolt). The spacer closest to the control arm is a rectangular plate that covers both bolts. The rear bolt goes all the way through the control arm, and requires a spacer within the control arm so it doesn't crush, but the front bolt only goes into the middle of the control arm. I have the sheet from the GM assembly manual that gives the dimensions and how they bolt together.
...that GM spec sheet seventy2plus2 mentions is also in this link........
http://66impalass427.tripod.com/id14.html