If I understand correctly, improvements/refinements were made through the years.
As a result, hoping for a complete unmolested rebuildable core off a 59 or 60
Many thanks!
Robert
-- Edited by -Robert M- on Sunday 4th of March 2018 09:36:39 AM
-- Edited by -Robert M- on Sunday 4th of March 2018 05:27:50 PM
DonSSDD said
Mar 4, 2018
do you have a metal tag number on your carb you have now? They may be the same for many years, or almost the same.
The Carburetor Shop in Missouri has the best kits and may have something in a usable core. They don't do rebuilds any more, but his kits have leather accelerator pumps, not neoprene which IMHO is junk with ethanol fuel. They tell you its good with ethanol, but most people see them fail in 6 months.
Jon will likely only sell you something if you have the correct tag number off your present Rochester.
-Robert M- said
Mar 4, 2018
Hi there Don.
Thanks for chiming in. It has an autoline rebuild tag and recently done, so I have no way of positively identifying. Its a suspect rebuild, I think done on a Friday afternoon when the guys wanted to go home. Screws all loose throughout, Choke housing really loose and leaking so wasnt sucking warm air through the tube off manifold. Linkage sloppy, thermostatic coil is wrong, lean and rich arrows pointing the wrong way. I am weird, stuff like that drives me nuts.
Have corrected what I can and it is satisfactory...
Havent removed yet to measure bore to see if correct for 261 vs. 235.
If I can get a known to be correct rebuildable unmolested core Ill get it redone by a good provider such as that you suggested, and keep my current one as a spare.
Appreciate any leads.
Sincere Thanks,
Robert
-- Edited by -Robert M- on Sunday 4th of March 2018 11:15:06 AM
4SPEED427 said
Mar 4, 2018
That is very unusual for Autoline. I've sold them at the counter for over 30 years and have had pretty much flawless performance from them. I'm surprised. Is it possible someone tinkered with it because it was rebuilt, used very little, then sat a while and was gummed up?
I plan to send my Qjet core to them for a rebuild and have full confidence in it coming back working great.
And the usual disclaimer applies, I've been wrong before!
JC2+2 said
Mar 4, 2018
Remembering back in the day of carburetors, the shop I worked at, we rebuilt in house and only replaced with Autoline when absolutely necessary. We got way too many flooding due to improper float height. It got to a point that before it went on, the top came off and float height rechecked. Also some of the throttle shafts were worn more than the core we gave them.
Carl, maybe they are better now but if your core is good I would get it custom rebuilt.
-Robert M- said
Apr 22, 2018
Greetings to all. Just a bump.
Rebuildable carburetor wanted for 1959 261 standard.
P/N 7013081
Thanks very much.
RGM
long stroke said
Apr 22, 2018
Robert, try calling CARB REBUILDER'S in Oshawa, Ontario. Talk to the man that runs it (Don Oake) and here is Don's number 1-905-438-0162. I have dealt with Don and his dad for about thirty years now and i doubt there is any better around. Don may have a carb or can point you in the right direction. Good luck.
-Robert M- said
Apr 23, 2018
long stroke wrote:
Robert, try calling CARB REBUILDER'S in Oshawa, Ontario. Talk to the man that runs it (Don Oake) and here is Don's number 1-905-438-0162. I have dealt with Don and his dad for about thirty years now and i doubt there is any better around. Don may have a carb or can point you in the right direction. Good luck.
Many thanks - will do.
a421cat said
Apr 29, 2018
I have a 1961 Carter carb for a 261. Car was automatic trans. Carb # 3114S. Carter kit is CK524. Hope this helps. Tag on my carb is 3114s and it comes up as a 1961 261 when I googled it.
Hello everyone.
Looking for carburetor for 1959 261-6 standard.
If I understand correctly, improvements/refinements were made through the years.
As a result, hoping for a complete unmolested rebuildable core off a 59 or 60
Many thanks!
Robert
-- Edited by -Robert M- on Sunday 4th of March 2018 09:36:39 AM
-- Edited by -Robert M- on Sunday 4th of March 2018 05:27:50 PM
The Carburetor Shop in Missouri has the best kits and may have something in a usable core. They don't do rebuilds any more, but his kits have leather accelerator pumps, not neoprene which IMHO is junk with ethanol fuel. They tell you its good with ethanol, but most people see them fail in 6 months.
Jon will likely only sell you something if you have the correct tag number off your present Rochester.
Hi there Don.
Thanks for chiming in. It has an autoline rebuild tag and recently done, so I have no way of positively identifying. Its a suspect rebuild, I think done on a Friday afternoon when the guys wanted to go home. Screws all loose throughout, Choke housing really loose and leaking so wasnt sucking warm air through the tube off manifold. Linkage sloppy, thermostatic coil is wrong, lean and rich arrows pointing the wrong way. I am weird, stuff like that drives me nuts.
Have corrected what I can and it is satisfactory...
Havent removed yet to measure bore to see if correct for 261 vs. 235.
If I can get a known to be correct rebuildable unmolested core Ill get it redone by a good provider such as that you suggested, and keep my current one as a spare.
Appreciate any leads.
Sincere Thanks,
Robert
-- Edited by -Robert M- on Sunday 4th of March 2018 11:15:06 AM
I plan to send my Qjet core to them for a rebuild and have full confidence in it coming back working great.
And the usual disclaimer applies, I've been wrong before!
Greetings to all. Just a bump.
Rebuildable carburetor wanted for 1959 261 standard.
P/N 7013081
Thanks very much.
RGM
Robert, try calling CARB REBUILDER'S in Oshawa, Ontario. Talk to the man that runs it (Don Oake) and here is Don's number 1-905-438-0162. I have dealt with Don and his dad for about thirty years now and i doubt there is any better around. Don may have a carb or can point you in the right direction. Good luck.
Many thanks - will do.