2024 Canadian Poncho Calendars are Now Available! CLICK HERE

 

 

Members Login
Username 
 
Password 
    Remember Me  
Post Info TOPIC: overheating


Veteran Member

Status: Offline
Posts: 26
Date:
overheating


Hello again:

     well I have repalaced the radiator, waterpump and thermostat and the car overheats in a nano second. I think I may have an obstruction in the engine block and am going to remove the freeze plugs and flush it. My question is what should I add to the cooling system (if Anything) before flushing. Is there an additive that I should run to help break up the blockage if there is one and then pop the freeze plugs?



__________________


Poncho Master!

Status: Offline
Posts: 1746
Date:

Don`t know what you have but have you checked the timing to make sure it is OK.



__________________


Addicted!

Status: Offline
Posts: 386
Date:

Do you still have the original flat head six in your car?  If so, there should be a water distribution tube in the block, that will often rust and block the water distribution making the engine overheat!  Sorry I can't remember how this tube is removed from block, but a good shop manual should help!  Hope this will help!  Bob.



__________________

 

1965 Thunderbird Special Landau 10th Anniversary Limited Edition only 4500 built 34,800 miles

 

 



Canadian Poncho Superstar!

Status: Offline
Posts: 6749
Date:

You could well have an air lock in there if it overheats pretty quick. With some engines you almost have to burp them.

__________________
Jerel


Guru

Status: Offline
Posts: 766
Date:

Is the temp gauge tell you is overheating? I think on your engine you have the electric gauge, if i'm right they are not so reliable.

If yes, I would suggest to use a infrared thermometer and look directly on the engine.

If directly on the engine there is really overheat, the back of the engine block is moslty full to the head of crap/mud/rust and it will need a physical action with a screw driver, compress air and water hose by freeze plug, and preferably the head removed. You can anyway doing a good job by the plug only to clean it.

Did you inspect the distribution tube when replacing the water pump? When the pump is on the bench, you can pull the distribution tube mostly by hand from the pump water hole passage in the block. If this tube is missing the back of the block, mostly near the exhaust passage, will missing fresh liquid.

Let us know.

Fitz.



__________________

www.FitzbackGarage.com Look for Easy Steering in your vintage Poncho, Look for the EasyDrive Power Steering System in the web site



Veteran Member

Status: Offline
Posts: 26
Date:

Hello Everyone:
Well the car is not overheating as I first suspected but it seems to be a grounding problem. The generator (12 volt) is putting out 12.5 volts but the regulator is putting out 16.5. I changed the system from 6 to 12 volts some years ago so now we will try to trace the ground problem that is making the temp gauge read funny. Thanks for the help and I will keep you posted.

__________________


Canadian Poncho Superstar!

Status: Offline
Posts: 5681
Date:

wwdaze wrote:

Hello Everyone:
Well the car is not overheating as I first suspected but it seems to be a grounding problem. The generator (12 volt) is putting out 12.5 volts but the regulator is putting out 16.5. I changed the system from 6 to 12 volts some years ago so now we will try to trace the ground problem that is making the temp gauge read funny. Thanks for the help and I will keep you posted.


 did you put a 12 to 6 volt resister in the temp guage [if electric]  maybe thats gone in the "pooper"



__________________

Some times I wake up GRUMPY, but today I let her sleep in    !!!!!!!! BLACKSTOCK Ont.



Veteran Member

Status: Offline
Posts: 26
Date:

Hey Everyone:

     I have changed the battery to engine ground, changed the wiring from the temp sender to the resistor that goes to the gauge. and It still shows that it is over heating under load. but as soon as I let off the gas and idle it goes back to 180 degrees. I am thinking of changing the sending unit out at a 100.00 bucks a pop. any more ideas before i order it??? Has anyone heard of them going bad? It is 60 years old. HaHa.

Bill



__________________


Guru

Status: Offline
Posts: 766
Date:

Is the temp gauge tell you is overheating? I think on your engine you have the electric gauge, if i'm right they are not so reliable.

If yes, I would suggest to use a infrared thermometer and look directly on the engine.

If directly on the engine there is really overheat, the back of the engine block is moslty full to the head of crap/mud/rust and it will need a physical action with a screw driver, compress air and water hose by freeze plug, and preferably the head removed. You can anyway doing a good job by the plug only to clean it.

Did you inspect the distribution tube when replacing the water pump? When the pump is on the bench, you can pull the distribution tube mostly by hand from the pump water hole passage in the block. If this tube is missing the back of the block, mostly near the exhaust passage, will missing fresh liquid.

Let us know.

Fitz.



__________________

www.FitzbackGarage.com Look for Easy Steering in your vintage Poncho, Look for the EasyDrive Power Steering System in the web site

Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.

Tweet this page Post to Digg Post to Del.icio.us
.
Support Canadian Poncho!
Select Amount:
<
.
.
.