2024 Canadian Poncho Calendars are Now Available! CLICK HERE

 

 

Members Login
Username 
 
Password 
    Remember Me  
Post Info TOPIC: 6-WAY POWER SEAT ?


Addicted!

Status: Offline
Posts: 165
Date:
6-WAY POWER SEAT ?


Hey guys,

 

 I just installed a 6-way power seat in a '69 Caprice (did not have a previous power seat) and want to get the seat to move back since it's practically hugging the steering wheel now. How do I wire it to a battery to move it back for now? Thanks!



__________________
RAJ REDDY


Canadian Poncho Superstar!

Status: Offline
Posts: 7418
Date:

There should be a 12 or so gauge orange wire coming from the motor on the power seat.  You can hook the directly to a battery and slide the seat back.  Just set the battery in the footwell and use some 12 gauge or larger wire to connect the battery (positive +) to the orange wire and to the frame of the seat (negative -)



__________________
70 2+2 convertible
70 2+2 hardtop
70 Parisienne hardtop
72 GMC Sierra

 

 



Addicted!

Status: Offline
Posts: 165
Date:

Great! Thanks for the tip. Now for the ground, I did notice a black small guage wire hanging from the seat with a ring terminal, I imagine this is for a ground wire. So I connect this wire to the negative side of the battery and the orange reddish large wire to the + side of the battery correct? Thanks again.

__________________
RAJ REDDY


A Poncho Legend!

Status: Offline
Posts: 48633
Date:

When I do this I usually use booster cables. Negative right to the seat track, positive to the orange wire and away you go.

Just make sure the positive clamp is insulated from any bare metal when doing this!

And yes, that black wire with the ring is the ground for it once you are doing the permanent install.

__________________

1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles 

1966 Grande Parisienne, 396 1 of 23 factory air cars



Canadian Poncho Superstar!

Status: Offline
Posts: 7418
Date:

I once tried doing a test with a small (10 amp) 12 volt power supply, but it couldn't provide enough current to run the seat, and the relay on the motor just clicked on and off very quickly.   That's why I indicated to use a car battery, it'll provide enough current.



__________________
70 2+2 convertible
70 2+2 hardtop
70 Parisienne hardtop
72 GMC Sierra

 

 



Addicted!

Status: Offline
Posts: 165
Date:

Hey guys, I went ahead and hooked up the battery cables (Positive + to the big orange wire and negative - to the seat frame). I hear the motor making a clicking noise when I engage the switch and feel the seat wants to move up and down as well as fwd and backwards though nothing? I WD-40's the heck out of the tracks and still nothing. For now, I went ahead an drilled some temporary holes to bolt the seat more backwards so I can actually sit in without my knees crunched against the dash.

__________________
RAJ REDDY


Canadian Poncho Superstar!

Status: Offline
Posts: 7418
Date:

It would be easier to diagnose if you had the power seat mechanism out of the car on the ground or on a table, with the seat removed.  Is it the relay clicking or the motor?  With the mechanism by itself, you can also remove the motor to see if it's siezed, etc.    Give it a try. 



__________________
70 2+2 convertible
70 2+2 hardtop
70 Parisienne hardtop
72 GMC Sierra

 

 



Member

Status: Offline
Posts: 21
Date:

When you tried working the power seat did take have car running? The seat draws alot of power and will click if you have weak battery and key is just on accessory or if you are hooked up to not enough current.

__________________


Addicted!

Status: Offline
Posts: 165
Date:

I just took the battery and put it on the front floor and threw the cables on (seat wiring not hooked up to car harness since the car never had a power seat to begin with). I'm pretty sure I here the clicking where the motor is (the orange,green blue lines connect to this looks like a junction box really).

__________________
RAJ REDDY


A Poncho Legend!

Status: Offline
Posts: 48633
Date:

It is likely the grease in there that has hardened. I've had a number of used power seats that I had to take apart, clean thoroughly and apply new lithium grease. You have to make sure you use a very light grease.

Our member here, cdnpont (Mark) did a tremendous technical post on restoring it-

canadianponcho.activeboard.com/t52070477/restoring-a-60s-vintage-gm-6-way-power-seat-unit/

__________________

1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles 

1966 Grande Parisienne, 396 1 of 23 factory air cars

Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.

Tweet this page Post to Digg Post to Del.icio.us
.
Support Canadian Poncho!
Select Amount:
<
.
.
.