2024 Canadian Poncho Calendars are Now Available! CLICK HERE

 

 

Members Login
Username 
 
Password 
    Remember Me  
Post Info TOPIC: How much force should it take to move the fuel pump rod?


Canadian Poncho Superstar!

Status: Offline
Posts: 6749
Date:
How much force should it take to move the fuel pump rod?


I bought a new fuel pump last week for my 283 and it takes major push to move the rod.  With my old ones I could push it with my hand without much difficulty but this one I have to grab it and push it down against the bench.  Is that normal or is this stiffer than what it should be?  I'd appreciate an expert opinion.



__________________
Jerel


Canadian Poncho Superstar!

Status: Offline
Posts: 6009
Date:

Sorry not an expert.winkBut depends on the pump I think. Have had a few where I have had to put the arm on a bench and push the pump down to be able to move it.



-- Edited by hawkeye5766 on Sunday 10th of July 2016 09:42:20 PM

__________________


A Poncho Legend!

Status: Offline
Posts: 48633
Date:

hawkeye5766 wrote:

Sorry not an expert.winkBut depends on the pump I think. Have had a few where I have had to put the arm on a bench and push the pump down to be able to move it.



-- Edited by hawkeye5766 on Sunday 10th of July 2016 09:42:20 PM



Ditto. To me, I would think that one you could compress with just your hands is weak.

__________________

1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles 

1966 Grande Parisienne, 396 1 of 23 factory air cars



Poncho Master!

Status: Offline
Posts: 2249
Date:

My Melling high volume fuel pump (for BBC) was very stiff, could not push by hand, during install I just slowly tightened the bolts to the motor and that provided pressure to compress it.

Dave

__________________

56Pontiac  1956 Pontiac Pathfinder 2dr sedan, 496 - dyno'd 545 hp, stick shift, 4.11 posi - Hot Rod

  1964 Acadian Beaumont SD convert, 283 - factory 195 hp, Powerglide, 3.08 10-bolt - Cruiser

  2012 US-built crew cab truck - Daily Driver and Boat Trailering



Poncho Master!

Status: Offline
Posts: 1057
Date:

The lever on the pump is very stiff, or at least should be.  The rod in the block that contacts with the lever should glide down very easily on it's own.  Put some grease on the rod in the block to hold it up while installing the new pump.



__________________

1951 Chevy Styleline -- Gasser

1966 Chevy Biscayne -- Sleeper

 



A Poncho Legend!

Status: Offline
Posts: 48633
Date:

Yes, or run a bolt into the front of the block that runs into the bore where the rod is to hold the rod up. I've never done it but I hear it's there for that reason.

__________________

1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles 

1966 Grande Parisienne, 396 1 of 23 factory air cars



Poncho Master!

Status: Offline
Posts: 1740
Date:

Carl Stevenson wrote:

Yes, or run a bolt into the front of the block that runs into the bore where the rod is to hold the rod up. I've never done it but I hear it's there for that reason.


 But don't forget to put the original short bolt back. Without it you'll have a big oil leak. Seen it before when guys change their own pump. A feeler gauge works good too for holding the rod up on install. 



__________________

'68 Parisienne 2+2 Convertible Matador Red (Resale Red but not for sale).



Canadian Poncho Superstar!

Status: Offline
Posts: 6749
Date:

Thanks guys. Other pump I was comparing to was almost brand new too but way easier to press. The Mexican one is the stiff one and the American one is quite easy. Will put her in and hopefully the fuel flows. Thanks again for the input.

__________________
Jerel
Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.

Tweet this page Post to Digg Post to Del.icio.us
.
Support Canadian Poncho!
Select Amount:
<
.
.
.