2024 Canadian Poncho Calendars are Now Available! CLICK HERE

 

 

Members Login
Username 
 
Password 
    Remember Me  
Post Info TOPIC: Timing verifying TDC with piston position and harmonic balance marks


Poncho Master!

Status: Offline
Posts: 2190
Date:
Timing verifying TDC with piston position and harmonic balance marks


There has been questions as to whether the harmonic balancer has shifted and giving inaccurate readings.

Is there a technique or tool for checking TDC without removing the cylinder heads?

 

 



__________________

Cliff

Done Hurryin

Like the larger type for my eyes. 

 

 



Canadian Poncho Superstar!

Status: Offline
Posts: 7176
Date:

Use a piston stop similar to this .. Rotate forward .. Mark the damper .. Then reverse . Mark and spite the difference .. There is tdc.

Attachments
__________________

later...rog

AADD supporting member !!
I'm a collector...not a builder!!Located in sunny central Saskatchewan at the lakehead!


Poncho Master!

Status: Offline
Posts: 1740
Date:

Has anyone tried if a long reach spark plug would do the same thing? Like out of a LS or vortec engine.

__________________

'68 Parisienne 2+2 Convertible Matador Red (Resale Red but not for sale).



Canadian Poncho Superstar!

Status: Offline
Posts: 10063
Date:

I used one of those on my 350 Roger. And I promptly bent it. cry

Don't be too rough with them, they bend easy. Probably designed to.

 



__________________
65 Laurentian post, 67 Grande Parisienne 4 door HT. 
 


Canadian Poncho Superstar!

Status: Offline
Posts: 7176
Date:

A person can improvise .. Theory is to stop the piston gently evileye



__________________

later...rog

AADD supporting member !!
I'm a collector...not a builder!!Located in sunny central Saskatchewan at the lakehead!


Addicted!

Status: Offline
Posts: 412
Date:

It's never occurred to me that the damper could slip and misalign with the timing marks. I'll definitely be checking that while assembling my engine this spring.



__________________

72 Nova SS,   66 Beaumont Sport Deluxe,   09 Pontiac Solstice GXP Coupe



A Poncho Legend!

Status: Offline
Posts: 48633
Date:

Yes, make sure you do. It's very common on old GM dampers. Sometimes just a little but over the years I've seen some in the shop that had turned inches!

__________________

1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles 

1966 Grande Parisienne, 396 1 of 23 factory air cars



Guru

Status: Offline
Posts: 652
Date:

Don't forget to back off the rocker arms before using a piston stop or you may up with a bent valve.

__________________

72 Nova SS - Minitubbed
70 Nova SS - #'s L-78 Bench Stick
68 Acadian SS clone - factory air
67 Chevelle rag - SS 427 clone



Canadian Poncho Superstar!

Status: Offline
Posts: 7176
Date:

Carl Stevenson wrote:

Yes, make sure you do. It's very common on old GM dampers. Sometimes just a little but over the years I've seen some in the shop that had turned inches!


 Yes,move had 2 different ones that have walked .. Found them during the build.. So who knows for sure how Many? 



__________________

later...rog

AADD supporting member !!
I'm a collector...not a builder!!Located in sunny central Saskatchewan at the lakehead!


Addicted!

Status: Offline
Posts: 280
Date:

Darn right they walk - had one walk clean off the crankshaft once !  Never did find it. no

Fred



__________________


Canadian Poncho Superstar!

Status: Offline
Posts: 6009
Date:

No fancy tool. Have always used pencil in hole and racked back and forth with flexbar.

__________________


A Poncho Legend!

Status: Offline
Posts: 20744
Date:

hawkeye5766 wrote:

No fancy tool. Have always used pencil in hole and racked back and forth with flexbar.


I was going to say. As long as you have a long enough pencil.blankstare 



__________________

Prince Edward Island

'64 Parisienne CS "barn find" - last on the road in '86 ... Owner Protection Plan booklet, original paint, original near-mint aqua interior, original aqua GM floor mats, original 283, factory posi, and original rust.



Canadian Poncho Superstar!

Status: Offline
Posts: 10063
Date:

hawkeye5766 wrote:

No fancy tool. Have always used pencil in hole and racked back and forth with flexbar.


 I've often thought of making a tube that you could thread in, then slip in a spring loaded pointer that would sense the piston, and transfer that moment to a fixed reference point on the end of the tube.



__________________
65 Laurentian post, 67 Grande Parisienne 4 door HT. 
 


Poncho Master!

Status: Offline
Posts: 2190
Date:

Mark

I really like that idea.   I have a friend who has a full machine shop in his garage and has done a couple of items that I needed to be created that required machining.

He is "retired" and does odd jobs.  I am sure that he would like a challenge like that.   He calls his part time business "The Inventors Tool Box."

Very skilled workmanship from what I have seen .. 

 

Thanks for all of the other contributions.

Cliff 



__________________

Cliff

Done Hurryin

Like the larger type for my eyes. 

 

 



Poncho Master!

Status: Offline
Posts: 1703
Date:

I broke the centre out of an old sparkplug and inserted a bolt then cut the head off. Worked a treat. Need to come around gently till piston touches, mark balancer, reverse rotaion gently until piston comes to stop. Mark and pointer should be dead centre of marks. If I can find it I'll post a pic.

I bought a degree wheel second hand off ebay and guage as well to check the camshaft dial in. Very handy. Was spot on to spec sheet.



__________________

cutting a roof off a four door is NOT a convertible.....

65 Parisienne convertible.one of 49 built for RHD export market,402BBC, T400, 2500 stally, posi rear, upgraded brakes with front discs, FUEL FAST efi custom built by me.

Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.

Tweet this page Post to Digg Post to Del.icio.us
.
Support Canadian Poncho!
Select Amount:
<
.
.
.