58-64 Full Size Chassis Tech

hanadam · hanadam

Hello all, This topic has probably been covered in the past, but I'm gonna ask anyways. Can I buy the disc brake kit for a 1963 Impala and bolt it right on my '63 Parisienne? Thanks in advance for any help. John

Pritch · Pritch

Hi, I am optimistic that someone on CP will be able to share a schematic diagram and hopefully a picture of the headlight switch wiring diagram on a '64 CS. I require the exact wiring colors and locations on the plug. Even though my switch has 8 spade connectors, there are actually 7 wires attached to...

Teich · Teich

Got these new tubular arms up and down seem to fit nice had minor fix for lower ball joint bolts. But issues have landed! that lower spring insulator has allowed spring to move out ie towards the ball joint just enough that spring now rubs the frame at top on out side this may show up in photos. any others ha...

posnick · posnick

Curious what everyone is doing to refinish theirs. Im sure a cast aluminum shaker can will work on the master cylinder but what about the alternator? Any issues with painting it? Not sure if it will retain heat and burn up

Recks · Recks

Is anybody running 16" wheels on their Poncho? I have a 1961 Strato Chief, looking at running 16x7 up front and 16x8 in the rear. Stock suspension / drivetrain. Any experienced tips to pass along? Back spacing? Tire size? Etc? Thanks!!

Bonne · Bonne

I am in the process of collecting parts to install a 6.0 LQ4 engine with a 4L60 transmission into my '64 CS. I have an opportunity to purchase a 8.2" complete posi and gear set with 3.36 ratio out of a "64? Nova. My question is will it go into my existing diff housing without any problems.

pontiacphil · pontiacphil

today I bought four 15 by 8 rally wheels for my 64 parisienne.my question is will 245 by60 bfgoodrich tires work on this car especially on the front without rubbing when turning the wheel.

Urban_suburban · Urban_suburban

so recently I replaced the power steering piston on my 64 custom sport. I bled it to the letter according to the shop manuals. I took it for a 20 minute drive and noticed the power steering was coming and going (this had happened last fall with the old piston too but went away) I put a new pump in as I had one a...

DonSSDD · DonSSDD

I can't figure out the top end of the floor shift steering column, the second outside piece from the top, what keeps that from turning on a floor shift car? Anyone got some pics from the assembly manual? This is the piece that has the shifter attached on a column shift car. Its for the 63, but I assume the 64...

pontiax · pontiax

rabbit64cs · rabbit64cs

This car was built by friends of mine in their shop Specialty Cars . the finished pics do not do the car justice,,,, it is finished in bare metal with a clear over it to protect it. The metal work is perfect , nothing hiding the workmanship ! The summer it was finished , he drove it to Sturgis SD, all over Al...

pontiacphil · pontiacphil

when pushing front of car down and up it is squeaking.without knowing which one,what is more likely,the shocks or bushings.

sphinx · sphinx

Hey does anyone know of or how to do a 59 strato disc brake conversion??? First time builder here..... So any info would be great thanks guys

jonathanD · jonathanD

Im looking at buying a 283 for my car and it comes with a frame from a 1964 full suspension if anyone needs its!

cantafforda2door · cantafforda2door

Hi guys. My brakes in the moredoor are sometimes going right to the floor but if i give it a quick pump they hold. I believe its the master cylinder. I have the power assisted brake booster on this car. Does anyone know if my master cylinder would be the regular style or a heavy duty model? I have the tw...

Lowfen · Lowfen

I would like to do a P.S. conversion on our Strato Chief. I have heard that there is a new style/updated 605(?) Saginaw box that is a direct bolt on to the 58 -64 Strato Chief chassic. Is there any one who knows about this box. I have done the ones where you needed the adapter plate and so on. Suggestions and o...

ZigZag · ZigZag

Does anyone know where I can purchase new front brake line/hose retaining clips? I check around with local auto parts stores and brake repair centers but they don't have them. The old ones rusted through and the new hoses didn't come with them.

drae_man · drae_man

Hi all, I acquired a 194 engine from a chevy 2 this weekend with an alternator and power steering pump. I'm hoping the brackets will work, just looking into what steering box I can run, that will bolt up. any ideas of what car might have one, i'd like to get a reman one, or new one, thanks!

drae_man · drae_man

Hi all, so while waiting on pricing on NOS and antique Chevrolet for brake cylinders, I found a set of fronts for a 65 Biscayne, which look very similar for the exception of the bleeder screw is shorter... i'm going to check them out tonight they are WC37079 and 78. It is 1.1875 which is the same as my car, ...

EL-Swervo · EL-Swervo

Hey Guys, I need to replace the front brake wheel cylinder seals and dust covers. I am in the UK and so do not have instant access to parts on the shelf for my car. My question is, are they the same as Chevy Impala? if so what year. I have been told that they share a lot of parts with '61 Chevy, is this correct? Th...

Topic		Started By	Replies	Views	Last Post
	1963 Front disc brake conversion (Preview) Hello all, This topic has probably been covered in the past, but I'm gonna ask anyways. Can I buy the disc brake kit for a 1963 Impala and bolt it right on my '63 Parisienne? Thanks in advance for any help. John	hanadam	2	2670	Oct 16, 2017 by hanadam
	'64 CS headlight switch wiring diagram (Preview) Hi, I am optimistic that someone on CP will be able to share a schematic diagram and hopefully a picture of the headlight switch wiring diagram on a '64 CS. I require the exact wiring colors and locations on the plug. Even though my switch has 8 spade connectors, there are actually 7 wires attached to...	Pritch	5	2810	May 25, 2017 by Pritch
	tubular lower control arm spring locater? ( 1 2 ) (Preview) Got these new tubular arms up and down seem to fit nice had minor fix for lower ball joint bolts. But issues have landed! that lower spring insulator has allowed spring to move out ie towards the ball joint just enough that spring now rubs the frame at top on out side this may show up in photos. any others ha...	Teich	25	6547	Nov 27, 2016 by Teich
	Master Cylinder and alternator (Preview) Curious what everyone is doing to refinish theirs. Im sure a cast aluminum shaker can will work on the master cylinder but what about the alternator? Any issues with painting it? Not sure if it will retain heat and burn up	posnick	9	3134	Nov 18, 2016 by posnick
	16" Wheels (Preview) Is anybody running 16" wheels on their Poncho? I have a 1961 Strato Chief, looking at running 16x7 up front and 16x8 in the rear. Stock suspension / drivetrain. Any experienced tips to pass along? Back spacing? Tire size? Etc? Thanks!!	Recks	7	6294	Nov 12, 2016 by top down
	LS install - need differential answers (Preview) I am in the process of collecting parts to install a 6.0 LQ4 engine with a 4L60 transmission into my '64 CS. I have an opportunity to purchase a 8.2" complete posi and gear set with 3.36 ratio out of a "64? Nova. My question is will it go into my existing diff housing without any problems.	Bonne	10	3286	Oct 31, 2016 by Paulish
	wheels would 7in. on front be better (Preview) today I bought four 15 by 8 rally wheels for my 64 parisienne.my question is will 245 by60 bfgoodrich tires work on this car especially on the front without rubbing when turning the wheel.	pontiacphil	13	4296	Sep 12, 2016 by paris63

	Help- 64 power steering issue (Preview) so recently I replaced the power steering piston on my 64 custom sport. I bled it to the letter according to the shop manuals. I took it for a 20 minute drive and noticed the power steering was coming and going (this had happened last fall with the old piston too but went away) I put a new pump in as I had one a...	Urban_suburban	8	2517	Aug 30, 2016 by MoboMac
	63-64 steering column (Preview) I can't figure out the top end of the floor shift steering column, the second outside piece from the top, what keeps that from turning on a floor shift car? Anyone got some pics from the assembly manual? This is the piece that has the shifter attached on a column shift car. Its for the 63, but I assume the 64...	DonSSDD	8	2201	Jul 7, 2016 by 409Safari
	Wanted: upper trailing arm frame bracket. 63-64 pontiac /chevrolet (Preview)	pontiax	5	2098	Jun 22, 2016 by 409Safari
	60 impala with upgraded 90's roadmaster under pinnings ! (Preview) This car was built by friends of mine in their shop Specialty Cars . the finished pics do not do the car justice,,,, it is finished in bare metal with a clear over it to protect it. The metal work is perfect , nothing hiding the workmanship ! The summer it was finished , he drove it to Sturgis SD, all over Al...	rabbit64cs	24	5132	Mar 11, 2016 by CdnGMfan
	squeaking (Preview) when pushing front of car down and up it is squeaking.without knowing which one,what is more likely,the shocks or bushings.	pontiacphil	5	2598	Feb 8, 2016 by Lad820
	59 disc brake conversion (Preview) Hey does anyone know of or how to do a 59 strato disc brake conversion??? First time builder here..... So any info would be great thanks guys	sphinx	2	2241	Jan 23, 2016 by sphinx
	Anyone looking for a frame (Preview) Im looking at buying a 283 for my car and it comes with a frame from a 1964 full suspension if anyone needs its!	jonathanD	2	1893	Dec 24, 2015 by Pontiacanada

	64 4door hard top brake question (Preview) Hi guys. My brakes in the moredoor are sometimes going right to the floor but if i give it a quick pump they hold. I believe its the master cylinder. I have the power assisted brake booster on this car. Does anyone know if my master cylinder would be the regular style or a heavy duty model? I have the tw...	cantafforda2door	12	3116	Nov 12, 2015 by cantafforda2door
	Power Steering Box (Preview) I would like to do a P.S. conversion on our Strato Chief. I have heard that there is a new style/updated 605(?) Saginaw box that is a direct bolt on to the 58 -64 Strato Chief chassic. Is there any one who knows about this box. I have done the ones where you needed the adapter plate and so on. Suggestions and o...	Lowfen	3	2558	Nov 11, 2015 by John Clawsie
	1964 Safari brake line retaining clips (Preview) Does anyone know where I can purchase new front brake line/hose retaining clips? I check around with local auto parts stores and brake repair centers but they don't have them. The old ones rusted through and the new hoses didn't come with them.	ZigZag	4	1609	Oct 29, 2015 by 67custom
	got a hold of a ps pump... what box to use? (Preview) Hi all, I acquired a 194 engine from a chevy 2 this weekend with an alternator and power steering pump. I'm hoping the brackets will work, just looking into what steering box I can run, that will bolt up. any ideas of what car might have one, i'd like to get a reman one, or new one, thanks!	drae_man	2	1387	Sep 4, 2015 by drae_man
	1962 laurentian Brake Cylinders - alternatives? (Preview) Hi all, so while waiting on pricing on NOS and antique Chevrolet for brake cylinders, I found a set of fronts for a 65 Biscayne, which look very similar for the exception of the bleeder screw is shorter... i'm going to check them out tonight they are WC37079 and 78. It is 1.1875 which is the same as my car, ...	drae_man	4	1853	Aug 24, 2015 by drae_man
	'62 Laurention front brakes, questions! (Preview) Hey Guys, I need to replace the front brake wheel cylinder seals and dust covers. I am in the UK and so do not have instant access to parts on the shelf for my car. My question is, are they the same as Chevy Impala? if so what year. I have been told that they share a lot of parts with '61 Chevy, is this correct? Th...	EL-Swervo	16	2969	Aug 22, 2015 by 427carl
«First < 1 2 3 4 5 … 8 > Last» \| Page of 8 sorted by