|
Swap the 6 for 8 327
(Preview)
Taking out a 230 6 cyl and dropping in a 327.I noticed different clutch sizes.From 9 to 11 inch clutch.Do I need to find a flywheel for this 327 to go in front of my 3 speed tranny?
|
hdboug
|
2
|
661
|
|
|
|
69 grandprix exhaust
(Preview)
anyone ever here of haveing springs on the bolts for the manifolds so it can flex the exhaust system...... when the motor is torking
|
otinabla
|
0
|
624
|
|
|
|
66 BEAUMONT POSI UNIT
(Preview)
hi guys. i found a 94 caprice cop car that has a posi rear end. any way this can be used in my 66 beaumont? both are 10 bolt units. cops are eating donuts, so i will have to be quick!
|
lorner
|
3
|
749
|
|
|
|
what motor did the gp originaly have?
(Preview)
i regestered my GP on the full size pontiac listing... and baised on the codes on the firewall tag it said the gp came with a "V8"... im wondering what it was thoo.. heres the info i got back from the tag info. Dec. 19th 1966 76657 V8 A (518 parchment) PEI link #...
|
dudemanbro
|
8
|
710
|
|
|
|
rear diff width on a 68 Parisienne 2+2
(Preview)
Just wondering how wide the rear diff on my stock 68 Parisienne 2+2 would be...a backing plate to backing plate dimension would be ideal...Thanx
|
52poncho
|
1
|
557
|
|
|
|
Tranny swap.
(
1 2
)
(Preview)
Anyone here done a 200R4 or a 700R4 swap in a 65-70? I'm planing on doing a 700 in place of a TH350. Cheers, Mark.
|
cdnpont
|
25
|
4573
|
|
|
|
Gauges, Gauges, gauges
(Preview)
My speedometer is broken aswell as my fuel gauge. I don't think it is my speedometer cable becuse I have taken it out and it is in one piece and still spins. My speedometer is the the extent of the far right. My fuel gauge goes to empty when I turn my car on and stays at what I think is the normal level when its of...
|
1993laurentian69
|
8
|
820
|
|
|
|
|
Hooker Headers
(Preview)
I have just put on new hooker longtube headers and I can't put the next piece of exhaust pipe on because the transmission crossmember is in the way. Any solutions? Ill post a pic if that helps. Custom make a new crossmember....?
|
1993laurentian69
|
24
|
1439
|
|
|
|
Where to get 1969 Laurentian parts?
(Preview)
I have a 1969 Laurentian and Im looking for parts. What other 1969 Pontiac models can I interchange parts with? It is a 350 btw. I can find tons of american model parts but no Laurentian parts :( Mostly looking for engine parts and exhaust.
|
1993laurentian69
|
10
|
980
|
|
|
|
1967 Pontiac Parisienne Repair Manual.
(Preview)
I'm looking for some type of repair manual for my 67 parisienne. Books, manuals, anything that would cover engine specs. My dream would to eventually overhaul the 327ci motor during the winter. Please post a link . I haven't found one yet anywhere. Thanks so much . Samie- -- Edited by Ghost on Sunday 12...
|
Ghost
|
3
|
3742
|
|
|
|
torque converter to flywheel
(Preview)
my torque converter is backed off right now and i was wondering if i need to wiggle it out a little or should the bolts just pull it into place it's only out by a 1/4 at most........ should i just put the bolts in tighten them a little bit then torque them down =)
|
jonathanD
|
6
|
794
|
|
|
|
engine is painted =)
(Preview)
well i spent the whole day working on my engine got it looking good
|
jonathanD
|
14
|
1183
|
|
|
|
It's alive =)
(Preview)
it took awhile thanks to pete for coming over thanks to randy for walkng me through it thanks to john for being john =) and thanks to everyone for there idea's ands support http://www.youtube.com/watch?v=NpWq-LXJ-rY
|
jonathanD
|
16
|
1153
|
|
|
|
removing a broken rocker cover bolt
(Preview)
so i went out to the engine today starting retiming it and noticed one of the rocker cover bolts is broken off what should i do to remove it?
|
jonathanD
|
8
|
755
|
|
|
|
|
vacuum leaks
(Preview)
i have alot of ports wide open if say i had a large enough vacuum leak could that mess with the air to fuel mixture enough to say make the car run very lean and not start. i say this i asked my autoshop teacher whatr was goin on and he said it sounds like a vacuum leak.....also when pete was here i put alot of fuel...
|
jonathanD
|
1
|
564
|
|
|
|
carl remember this?
(Preview)
Hey carl i added a couple things to those valve covers you gave me =) don't worry the oil breather came from the old 283 and soo did the oil filler but showing you this might give away my whole engine scheme... you should see the old air cleaner HAHAHAHA
|
jonathanD
|
6
|
1233
|
|
|
|
starting issue's still.......
(Preview)
this engine is being a total bitch it's still going no where in a hurry. so i set up the new cap and rotor as you can see by the pictures it is facing the right way and it is at TDC. anyone have an idea what could be wrong?
|
jonathanD
|
12
|
1147
|
|
|
|
replaced the cap =)
(Preview)
hey guys i just replaced the dist cap(on sale) 12 bucks on my car was going to try it again but my battery charger is not working i just bought it 40 min ago lol im heading back now. if this does not work what should i try next? -- Edited by jonathanD on Thursday 26th of May 2011 06:32:07 PM
|
jonathanD
|
0
|
654
|
|
|
|
Met with dualquadpete today
(Preview)
I got a phone call from pete saying he is a little early and he is in whitby. so he came to my school and picked me up crazy eh? then we headed to my house. so he showed me how to fix the timing. and we almost had her going but the battery died again and i need a new cap the one on the engine is cracked and is causing...
|
jonathanD
|
17
|
1006
|
|
|
|
starting issue
(Preview)
so my engine is timed and she still won't kick over when she was trying looks like lint or mouthballs coming out of the cylinders im thinking it might be my battery it might be low because everything is slowing down... but i'm not back firing anymore and smoke is coming out of the right exhaust port at the...
|
jonathanD
|
21
|
1017
|
|
|