|
compression check numbers
(Preview)
Hi all, did a compression check yesterday, two at 150, two at 130 one at 140 one at 135 one at 145 and one at 80. the low one must be where it was siezed? what are your thoughts on this? will the rings seat at some point in the low one or is the engine toast? sure runs nice! thanks Woody
|
woodytwoshoes
|
4
|
948
|
|
|
|
12 bolt ring bolts
(Preview)
Do you reuse the factory bolts if they look perfect? Or get new ones? If the answer is new what manufacturer? Part number? Thanks
|
SGS Welding
|
9
|
1102
|
|
|
|
carb swap
(Preview)
Hi all, got the old carb off, studs look suspiciously deteriorated. Any ideas on how to proceed? Thank you Woody
|
woodytwoshoes
|
19
|
1613
|
|
|
|
283 timing question
(Preview)
Hey all, have all the plugs out, turned the engine to no 1 cylinder at the top, lined up the timing marks to zero on the crank. The rotor points to no 7 cylinder. Makes no sense to me. any help or ideas would be most welcome, Thanks Woody
|
woodytwoshoes
|
11
|
876
|
|
|
|
fuel type for 66 283
(Preview)
Today in the coffee shop a car guy said the old motors don't like the new fuel and run too hot. Is there a cure for this? additive? Woody
|
woodytwoshoes
|
6
|
794
|
|
|
|
ignition
(Preview)
Hello all, got it ready to start today and it turns over but no fire. cleaned points tried again, same thing no fire. should i just swap out the cap and rotor, points and condenser and new wires and see what happens? Also i may have put the rotor on backwards, how do i tell? i know i should have taken a pic befo...
|
woodytwoshoes
|
6
|
938
|
|
|
|
carb linkage return spring for 283
(Preview)
do you guys know where i can buy the return spring for the carb linkage? 283 two barrel Thanks Woody
|
woodytwoshoes
|
10
|
906
|
|
|
|
|
Video describing the function of different differential types.
(Preview)
Long vid, but the fellow is very straightforward and practical with the details of the most common differentials.
|
cdnpont
|
0
|
638
|
|
|
|
Carl's new 427 build thread.
(
1 2 3
)
(Preview)
|
cdnpont
|
59
|
3787
|
|
|
|
12 Bolt Posi Shaft Lock Bolt
(Preview)
Has anyone bought an aftermarket lock bolt for a 12 bolt posi? I searched quite a while online and most of the ones listed sounded wrong or if they had a picture, looked wrong. I finally checked and luckily one of the only 2 dealers left with one of these discontinued parts was local so I bought it. I'm cu...
|
4SPEED427
|
7
|
1020
|
|
|
|
Adding engine oil to gas tank
(Preview)
So.....I was thinking about my grandfather recently, and a random thought came to my mind and of course it got me thinking. I have a memory of being with him at a gas station in the 1980s. I think we were in his 1977 Buick LeSabre. It was a full service station and my grandfather opens the trunk. He gets ou...
|
Kevin66427
|
9
|
940
|
|
|
|
QJet Gurus: How do I speed up the "off choke"?
(Preview)
Gurus; How do I get my Qjet to come off the choke a little quicker in the cold? On my 327 when I rebuilt it, I did the partial restriction of the heat riser passage at the intake gasket, and I used a gutted heat riser as well. Even when I see 180 on the gauge, she still stays on high idle when out on the road, until...
|
cdnpont
|
5
|
1718
|
|
|
|
recommendations for suppliers crate engines
(Preview)
Im in BC, any recommendations on companies that sell crate engines? I talked with CCE in Burnaby and they seemed good, but im sure you guys have been through the process of buying one or two. Love to hear your take on this. Thanks Woody
|
woodytwoshoes
|
6
|
1214
|
|
|
|
crate engine and trans
(Preview)
so, just priced a 350 crate engine (300 hp) and 700R4 trans, with all the extra add ons 12K What do you think people? advice welcomed. Woody
|
woodytwoshoes
|
14
|
1218
|
|
|
|
|
1969 427 Grande Parisienne
(Preview)
I have a 1969 Pontiac Grande Parisienne 4door 427 V8 335 hp , but it has dual exhaust. It is original and my grandfather bought it in 1969 from Roy Pett GM in Lindsay Ontario. It has never seen a Canadian winter. It went to Florida until 1981. Stored for 28 years it looks a little rough but it is all there. A li...
|
Harvster
|
23
|
2341
|
|
|
|
Help identifying 4 speed bench seat handles.
(Preview)
Tonight I went on a mission. I'm trying to sort out what bench seat shifter handles fit what cars, and what each one looks like. Quite a bit of info online but from what I can tell, LOTS of wrong info on this topic, so I dug into the limited resources I have. From what I can find, from 64-67 Canadian Pontiacs...
|
4SPEED427
|
15
|
1346
|
|
|
|
AT/MT Quadrajet. What is the difference between the two?
(Preview)
What physical differences are there between an automatic coded Q-Jet compared to a manual one? I have a 1967 7027202 as came standard on my 67 327 automatic. Just wondering as the engine is now mated to a manual. Also, the carb was pro rebuilt about 9 years ago by Carburetor Rebuilders. it has sat dry fo...
|
cdnpont
|
15
|
2810
|
|
|
|
Car sits for a week Holley carb bowls are dry.
(Preview)
Hello, I have had a few Holley carbs in my day and never had them go dry Recently I got a 67 Beaumont , all is good but then it sits the carb bowls go dry (About a week) Stay Safe
|
67-Beaumont
|
14
|
1297
|
|
|
|
Anyone ever have needle bounce with a new speedo cable?
(Preview)
New extra long cable to the 4 speed. Needle started off decent, but now is bouncing wildly. Any solution to the issue? Anyone experience the same? Thanks, Mark.
|
cdnpont
|
20
|
1072
|
|
|
|
SBC Main seal question,
(Preview)
Question; Can one change a SBC 2 piece seal with the engine in place, in a 65 B Body? I have just detected a small drip in the 65. Don't think its the pan. If it stays this small I'll not worry too much. Second, Will this wee drip eventually foul my clutch?
|
cdnpont
|
3
|
814
|
|
|