|
Some good info and Roller cam advice
(Preview)
Engine in the car I purchased was built by a local reputable shop and they were kind enough to send me the internal details and even the dyno sheet. Pretty happy with the 414 HP / 419 TQ combo from the alum headed 350 vortec block. Was even happier to see it has a roller cam, but here comes the cringe worthy...
|
68vert
|
8
|
216
|
|
|
|
need advice
(Preview)
does anybody know how to tell the difference between the 396 325 hp or 350 hp my vin starts with 738378 i dont know if that helps it is a 1968 beaumont s d -- Edited by citywide on Sunday 8th of November 2020 05:27:24 PM -- Edited by citywide on Sunday 8th of November 2020 05:32:12 PM
|
citywide
|
5
|
276
|
|
|
|
65 beaumont exhaust header issue
(Preview)
My dear CP folks, here comes interesting issue I ran across my 65 Beaumont w/V8 engine install last year and now I'll have to clarify what I'm gonna do in the end to get the issue sorted out and get the car running. As the car originally came with a L6 190 ci engine, I had to install the V8 option frame mount...
|
Beau_SD_65
|
4
|
630
|
|
|
|
64 Beaumont help needed---speedometer cable length?
(Preview)
I am hoping someone has a speedometer cable out of a 64 Beaumont with a Powerglide and is able to measure the length of it. Our site member "Winnipeg" has asked me to see if I can order him a new one and I never trust the jobber catalogues. My experience with their applications has been that they might make s...
|
4SPEED427
|
10
|
439
|
|
|
|
Rad cap with overflow
(Preview)
Hello, I have just installed a radiator overflow and was wondering if I have to change the radiator cap now and if so would you know the number?
|
zak404
|
6
|
427
|
|
|
|
69 BOP 8.2 posi swap
(Preview)
Our good friend JC2+2 is rebuilding my diff, putting in a Richmond posi with 3:55 gears. Is there supposed to be a spacer for the ring gear to line everything up?
|
Captain Beaumont
|
17
|
558
|
|
|
|
M20 or M21 ?
(Preview)
I just finished rebuilding an M21 transmission and got to thinking maybe I should swap out the M20 for the M21. But first maybe I should determine which trans will be a better all around trans for my car. The car has a 3.08 gear Posi the tires are 25.6 inch diameter. The M20 currently in my convertible is an...
|
ROSIES CAR
|
12
|
761
|
|
|
|
|
66 beaumont carburetor
(Preview)
Hoping someone could help determine what carb would have come originally on a 66 beaumont. It has a 327 with a power glide. Thanks Stan
|
1966SD
|
13
|
643
|
|
|
|
4 Bolt Main 327 Blocks
(Preview)
There is another thread about 327's that has slightly derailed so rather than take it further off course, I'll post separately. The discussion came up that there has been rumours for years (I first heard them in the 70's when I was a teenager) that GM made some 4 bolt main 327's. The Massey Ferguson comb...
|
4SPEED427
|
22
|
1311
|
|
|
|
Engine keeps running after ignition is switched off.
(Preview)
I have a recent problem that started a couple weeks ago. It was really brief the first couple times and was just a second or two. Engine doesnt diesel it runs just like the key is still on. Yesterday it was probably 5-6 seconds. Havent had any issues with the ignition switch doing everything else it is sup...
|
jmont64
|
8
|
731
|
|
|
|
L79 327 in a chevelle beaumont does it have a 3/8 fuel line
(Preview)
Does a 1965 L79 chevelle or beaumont have a full 3/8 fuel line from the tank along the frame?
|
beaumontguru
|
6
|
653
|
|
|
|
Exhaust manifold gaskets yes or no?
(Preview)
from the factory no gaskets but things mating surfaces are not as good as new
|
70 SS ACADIAN
|
22
|
862
|
|
|
|
67 Beaumont auto to standard conversion
(Preview)
Has anyone converted a 67 Beaumont from an automatic to a standard and if so, what pedals did you use? Pedals from a 67 GTO/Tempest or 67 Chevelle because apparently they are different?
|
Birgs
|
11
|
1036
|
|
|
|
Installing a fuel pressure regulator...
(Preview)
Hi fellas, I'm running an Edelbrock 800cfm carb on the 396/402. I'm also running an Edelbrock Victor Jr high volume fuel pump. It supplies the carb with consistent 9psi. I'm just learning now (because I failed to read the Edelbrock manual) ...that Edelbrock carbs require no more than 6.5psi. Has...
|
jlysholm
|
1
|
597
|
|
|
|
|
Transmission Issue
(Preview)
My turbo 350 transmission doesn't shift into 1st until you have sat at a light for about 20 seconds? The fluid level is up, I don't think the linkage position would affect it? In automatic mode it wouldn't stay in low past 3000 RPM under full throttle, in spite of adjusting the linkage which doesn't seem...
|
zak404
|
5
|
840
|
|
|
|
Carb
(Preview)
I was thinking of taking out my Rochester carb and going with a Holly or Edelbrock. Any body have an opinion would be appreciated.
|
JJ
|
4
|
744
|
|
|
|
64 Beaumont powerglide cooling lines?
(Preview)
Just finishing up installing the powerglide back into my 64 Beaumont SD. Have a question on how to tie in the transmission cooling lines to the radiator. Attached scan shows the locations of the cooling lines on the transmission case but question is how do the lines attach to the cooler in the radiator...
|
norontcan
|
2
|
752
|
|
|
|
Converting to HEI
(Preview)
I've read all of the "real men and women use points" but at the risk of the ribbing, I want to convert my 230ci to HEI. As i'd like to have it done professionally, i am asking the Winnipeg experts on here who have been so helpful in the past if they can recommend anyone in the Peg who could do this correctly? Th...
|
Winnipeg
|
15
|
1180
|
|
|
|
what oil recommendation
(Preview)
ok guys 454 bb what oil recommendations please apparantly need zinc any one using joe gibb HR-1 Conventional 15W-50 recommended for muscle cars
|
marshalldude
|
20
|
6205
|
|
|
|
Engine ID Canadian 283
(Preview)
Someone was asking me about the engine numbers for their '66 Chevelle 300 convertible with a 283. I can't figure out the Canadian engine numbers prior to the '67 models. The engine i.d. is 776547430. Can anyone decode this engine for me?
|
CdnGMfan
|
2
|
1468
|
|
|