Ok gang, need some answers on this, going to look a 58 Poncho 2 dr sedan this wknd. needs frame replacement, & I figure if I slide some 4x4's under body & lift it off frame, then support the 4x4's on jack stands, this "should hold the body" Will I have to brace it or not, don't think it will FLEX, BUT I could be wrong, as I have many times before!!!! a rotessary would be great, as floor pans are bad, so the seller said, but I don't have one & they ain't cheap,but I am, will have to see how bad this is & if I want to get into a "major" winter project. Seller said he has good frame & floor pans as well. Pete
__________________
Some times I wake up GRUMPY, but today I let her sleep in !!!!!!!!BLACKSTOCK Ont.
I used 2"x4" and 4"x4" and placed it on 6 casters to make it easy to move it around the shop and to push it in and out of an enclosed car trailer for trips to the media blaster and paint shop.
That looks like it would work, hope you don't have a patent on it. Only problem I see, I don't have "that" many friends to help out!!! Mention physical labour & they are "GONE"" Pete
-- Edited by dualquadpete on Tuesday 22nd of September 2009 06:33:27 PM
__________________
Some times I wake up GRUMPY, but today I let her sleep in !!!!!!!!BLACKSTOCK Ont.
If the floors are really weak you may want to consider tack welding in a temporary brace at the door jambs before you lift it. That will help keep it from distorting when you do cut out the floor.
That looks like it would work, hope you don't have a patent on it. Only problem I see, I don't have "that" many friends to help out!!! Mention physical labour & they are "GONE"" Pete
-- Edited by dualquadpete on Tuesday 22nd of September 2009 06:33:27 PM
Haha, you beat me to it. As I was reading that, I had the same thought. Where would I find that many friends, especially if I buy a 66 Grande Parisienne. How many friends would that take???!!!
__________________
1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles
1966 Grande Parisienne, 396 1 of 23 factory air cars
The Corvette bodies are a lot easier to lift. I've participated in a few lift offs. I would say the lightest was a 56. As for a 58 Pontiac you may want to get 2 sets of chain falls with some sturdy overhead beams to hang them from. It has got to be some heavy metal. Good luck.
That looks like it would work, hope you don't have a patent on it. Only problem I see, I don't have "that" many friends to help out!!! Mention physical labour & they are "GONE"" Pete
-- Edited by dualquadpete on Tuesday 22nd of September 2009 06:33:27 PM
Haha, you beat me to it. As I was reading that, I had the same thought. Where would I find that many friends, especially if I buy a 66 Grande Parisienne. How many friends would that take???!!!
hey we did my 69 Beaumont stationwagon-10 guys! It was a heavy pig but we gotter done!!
After help taking off the complete nose I used to do the frame swaps myself.. I'd hang two comealongs from a hoist beam w/ one hooked to the hinge locations of each side of the cowl and an engine hoist in the middle at the rear so the open front kept it clear to roll the chassis in/out.. I'd undo the firewall harness from the cowl and master from the booster (so no lines cracked open) also undo the e-brake cable and fuel lines between the chassis and tank/f-pump.. There'd be the odd ground and wiring to rear bumper lights if equipped but aside from that it'd be an easy in and out w/ the frame then reverse order the above and you're on the road without even bleeding the brakes!.
__________________
I like real cars best...especially the REAL real ones! ----------------------------------------------------------------
Thanks folks, will let you know what the outcome is after I go see It. it may be too far gone for me, or maybe not, will have to check it out "real good" as he didn't say anything about the trunk floor or door jambs, rear whl. hsgs. etc. Doors were off in Picture, think I'd put them back on before attempting body lift, to sriffen the "hulk" pete
__________________
Some times I wake up GRUMPY, but today I let her sleep in !!!!!!!!BLACKSTOCK Ont.
Never had the luxury of overhead beams; I've always jacked the car up, supported it on blocks & beams or saw horses, and rolled the frame out/in. One person can do it; it just takes longer.
I spoke to the guy yesterday and am going to look at the car tonight.
I was told it has a bad frame, floors, rockers, and a few other places are soft.
I have done a bunch of frame offs and depending on how good the floors and rockers are - you might have to brace the body to make sure it doesn't sag or twist. I use 1x1 box through the car to support it, and 1x2 channel for the lift points.
If the car is structurally solid, you can usually just make something to hold the body and be fine. Make sure you have enough space for 3 cars if you are going to do this - the frame, the body, and all the other parts.
Have about 10 people if you are going to lift it off by hand! It took us about that to do a 69' Cutlass body.
-- Edited by RacerRick on Thursday 24th of September 2009 10:06:55 AM
I spoke to the guy yesterday and am going to look at the car tonight.
I was told it has a bad frame, floors, rockers, and a few other places are soft.
I have done a bunch of frame offs and depending on how good the floors and rockers are - you might have to brace the body to make sure it doesn't sag or twist. I use 1x1 box through the car to support it, and 1x2 channel for the lift points.
If the car is structurally solid, you can usually just make something to hold the body and be fine. Make sure you have enough space for 3 cars if you are going to do this - the frame, the body, and all the other parts.
Have about 10 people if you are going to lift it off by hand! It took us about that to do a 69' Cutlass body.
-- Edited by RacerRick on Thursday 24th of September 2009 10:06:55 AM
OK now I know who Eric is, guess you came to the same conclussion I did, it's too far gone for me, maybe you too!!! Pete
__________________
Some times I wake up GRUMPY, but today I let her sleep in !!!!!!!!BLACKSTOCK Ont.
Never had the luxury of overhead beams; I've always jacked the car up, supported it on blocks & beams or saw horses, and rolled the frame out/in. One person can do it; it just takes longer.
that's how i did mine john. lifted each end a bit at a time.
OK now I know who Eric is, guess you came to the same conclussion I did, it's too far gone for me, maybe you too!!! Pete
I looked at it and the owner said would sell it cheaper without the engine and rims since he is looking at a another car that could use them.
Its too rough for me to tackle right now - I already am in the middle of the 55' Chevy build which is a frame off. I was hoping it was solid enough that I would just sell the 55' and build that instead.
I did just pick up a 73' Buick Electra 225 that I am going to use the engine out of in the 55'. I figure a mild 455 should work pretty good on that wagon.