very interesting story about how Camaros were built in Norwood and Van Nuys  in 1969, i assume Oshawa was close to the same?

Fisher Body Operation Details

Fisher Body - Body Shop Operations

The body shop is broken down into five major areas - subassemblies, underbody, side frame lines, body framing, and body-in-white final operations. Raw stampings are shipped in from many Fisher stamping plants and outside suppliers; most welding was done with spot-welding guns, although some final operations used mig-welding.

Subassemblies: Many major subassemblies were built up in precision off-line fixtures and conveyed to the side frame or body framing lines, including:

 

• Rear compartment pan - trunk floor and rear frame rails.
• Front floor pan - main floor pan, seat and subframe mount reinforcements, floor shift piercing, cutouts and reinforcements.
• Cowl & dash - dash, air intake plenum, cowl top, side panels, upper and lower instrument panel.
• Windshield and backlite upper headers.
• Rear wheelhouse assembly (inner and outer) with quarter inner panel.
• Front body hinge pillar/windshield side frame inner and outer and reinforcements.
• Side roof rail assembly (inner and outer).
• Rear shelf panel with deck lid hinges, torsion rods and rear seat bulkhead panel.

Underbody: The rear compartment pan, front floor pan, cowl and dash, and rear shelf panel subassemblies were welded together to form a complete underbody after being loaded to a precision steel body carrying truck on wheels with locators for each subassembly; this "build truck" carried the body all the way through the body framing line, and then returned on its continuous-loop conveyor to pick up another group of subassemblies.

Side Frame: Large assembly fixtures the length of the body were suspended vertically from a continuously-moving overhead conveyor; these were continuous-loop conveyors, one for the RH side, one for the LH side, across the aisle on both sides of the body framing line. All the body side components were loaded outside-first, in car position, and welded sequentially as the conveyor moved along, including the outer rocker, outer quarter, wheelhouse and quarter inner, front body hinge pillar, roof rails, rocker inner, and miscellaneous brackets and reinforcements depending on the body style. Separate side frame fixtures were scheduled for coupes and convertibles. At the end of the side frame line, the assembly was a one-piece body side panel, ready to be transferred into the body framing line and joined to the finished underbody assembly.

Body Framing: As the body build truck entered the framing line carrying the completed underbody, the side frame fixtures shuttled in from each side and were locked in place against locators on the build truck; two pairs of diagonal crossbars were added to tie the side frame fixtures together at the top, the upper windshield and backlite headers were loaded, and hundreds of spotwelds were made to tie the side frame assemblies to the underbody. After the headers were welded, the crossbars were removed, the cowl tag was installed, and the roof skin, tulip panel (the panel between the backlite and the deck lid opening), and rear end panel were loaded and welded. At the end of the framing line, the body was lifted and transferred to a simpler, lighter carrying truck, and the precision body build truck returned on its loop conveyor back to the underbody line.

 

Body-In-White Final Operations: The side shroud ("saddlebag") outer panels and the doors and deck lid were installed and fitted, followed by soldering and metal-finishing the roof-to-quarter joint, metal-finishing exposed spotweld flash, stud-welding for windshield and backlite and vinyl top molding retainers, option and spoiler drilling, mig-welding the dual exhaust hanger (for 1969's, if applicable), final metal-finish, body cleanup, and inspection. Once complete, the body and loose cowl vent panel were shipped upstairs to the Paint Shop.

Most Body Shop repairs were handled on-line (dings, dents, metal-finish, solder repairs, missing weld studs, missing welds, etc.), but there were off-line stalls for major metal repairs, panel replacement, and similar issues that required the body to be stationary for an extended period.

Fisher Body - Paint Shop Operations

The Paint Shop is broken down into phosphate, prime, sealing, and color departments; the body was suspended from an overhead conveyor with hooks at the firewall and at the ends of the rear frame rails through the phosphate system, and was transferred to a steel carrying truck before the prime system that carried it through the rest of the Paint Shop and through the Trim Shop.

Phosphate System: The raw body shell passed through a seven-stage phosphate system, where it went through a series of enclosed high-pressure hot spray stages where it was washed to remove all the oils and debris from stamping, welding, brazing, soldering, and grinding operations, then the body was coated with a hot iron phosphate solution which "etched" the metal and provided "teeth" for paint adhesion. The final stage was a de-ionized hot water rinse and blow-off, followed by a drying oven on the way to the prime booth.

Prime System: In the first prime booth, the entire body, inside and out, was manually sprayed with primer, and confined areas subject to corrosion were given a second coat of heavier primer material; this prime coat was then baked at 390F for 30 minutes. In the second prime booth, the instrument panel and rear of the shelf area (and the upper door and quarter areas of 1967-68 models) were painted interior color, and another coat of air-dry flash primer was sprayed from the belt line down. The interior color areas were masked, and the entire outer body was sprayed with gray primer-surfacer and the body was baked again at 285F for 45 minutes. The cowl vent panel was hung in the side window opening on wire hooks all the way through the paint process.

After baking, the entire outer surface was wet-sanded, wiped down, and the body went through a short infra-red dry-off oven on its way to the sealer deck.

Sealing: The primed and baked body passed through a long series of platforms where vinyl plastisol sealer was applied to all joints; floor pan drain hole plugs were installed and sealed, and the sealers were manually dressed in exposed areas. Floor pan deadener pads were then installed, which "melted" into place later in the color reflow oven. The body then went through a sealer oven to "set" the sealers on its way to the color booth.

Color System: The bodies were sequenced to "batch-paint" by color as much as the build schedule allowed, to minimize the waste of thinner required to clear paint guns between colors. The interior was masked off, the body exterior was tacked-off, and it then entered the main color booth, where it got three coats of acrylic lacquer, sprayed automatically with vertical and horizontal reciprocating spray guns, with a 3-minute "flash" between coats, followed by a 10-minute bake at 200F to "skin" the surface prior to sanding. In the next stage, any surface defects were power- and hand-wet-sanded with mineral spirits, then wiped off prior to entering the final "reflow" oven. This bake lasted 30 minutes at 275F, where the lacquer surface softened and "re-flowed" to a uniform gloss.

The last process for a non-stripe car was the blackout booth, where the firewall was blacked-out, the trunk was sprayed with spatter paint, and sound-deadening undercoat material was sprayed in the rear wheelhouses. The rear "****tail shakers" on convertibles were suspended in the trunk for spatter painting, but weren't bolted in place until later in the Trim Shop, after the taillights and marker lights were installed.

If the car required Z28, Z10, or Z11 stripes or a black rear end panel or rockers, they were masked and manually sprayed in the in-line repair booth/oven system after the reflow oven, including the cowl vent panel; spoilers were painted body color separate from the body, and were final-installed to the deck lid just prior to the repair booth. The rear window filler panel, deck lid and spoiler were masked and sprayed stripe color in the repair booth, and baked in the repair oven before the body went back downstairs to the Trim Shop. The paint guns in the repair booth were fed from manifolds that were part of the main color circulating system so that the repair booth used exactly the same paint the main color booths were using.

If a unit required a major paint repair that couldn't be accommodated in the normal in-line cycle time, it could be diverted off the main line at the end of the repair booth into a parallel loop that ran in the opposite direction and fed the unit back into the main line ahead of the main repair booth; the re-run loop could accommodate about 20 units.

 

Paint System Information

The Fisher paint booth had pneumatically-driven overhead and side guns that reciprocated cross-car and up-down on trolleys, and were fed from manifolds on one side of the booth. Each booth had about 20 paint circulating systems fed from the main Paint Mix Room - usually 14-16 for standard colors and several others for thinner and one spare, and there were separate manifolds for hand-held manual spray guns used for interior and cut-ins. Every time that consecutive cars had different colors, all of those guns had to shoot thinner from the manifolds to the guns (through the floor grates) to clean out the previous color, then charge the line with the new color before they could spray again, and that had to take place in about four seconds.

Paint came from DuPont in 500-gallon tote tanks, with paint mixed from the same lot distributed to both the Fisher and Chevrolet paint shops to minimize color match and gloss issues between the body and the front sheet metal.

Special order paint colors were done by dragging 5-gallon pressurized paint pots through the booths and manually spraying everything; if there was a fleet or special order large enough, they charged one of the spare circulating systems, but that didn't happen very often - it didn't pay to charge a spare system for less than 100 cars.

Scheduling

Bodies were scheduled to maintain assembly line work station balance. The Body Shop build sequence took into account the scheduling priorities for the Paint Shop and the required sequencing for Fisher Trim Shop work station balance. Stripes and 2-tones were the high labor content units for the Paint Shop and were scheduled so that they were not run consecutively. The schedule priority for the Trim Shop was vinyl tops and convertibles. Those limiting factors determined whether or not batch painting made sense, as bodies entered the Fisher Trim Shop in the same sequence in which they left the Paint Shop; i.e., you didn't want six vinyl top jobs in a row in the Trim Shop (which would really tear up the line balance) just to save some thinner in the Paint Shop

Fisher Body - Trim Shop Operations

When the body was released from the Paint Shop and it was sequenced into the delivery conveyor to the Trim Shop, Fisher's computer generated their version of a "Broadcast Copy" for each car, called a "UOIT" (Uniform Option Identification Tag), which identified the color, trim, and options information for the Trim Shop build of that particular car; that document was placed on the car at the transfer station for worker reference. (CRG is actively searching for additional copies of these UOIT papers - please contact the CRG if you can supply us with a copy.)

Wiring and the roof insulator went in first, followed by the headliner and sail panel and shelf trim and garnish moldings (and rear speakers or defroster if ordered), and the windshield and backlite opening flanges had the molding clips installed and were primed for later glass installation (vinyl tops went on ahead of this so the rear edge could be trimmed in the backlite opening before glass priming). Convertible windshield frame trim moldings and latch hardware were installed, along with the power top mechanism, plumbing, and wiring.

Convertible tops were built up on an off-line merry-go-round fixture, then carried to the line where the installation was completed; a protective shipping cover was installed over the top skin after final inspection before the body was shipped to Chevrolet.

Door and deck lid locks were installed. The lock/key package was a Fisher Body item picked at random out of a bin - it came in a 2-part bag; Fisher tore open the half with the door and deck lid cylinders and installed them, and taped the other half of the bag to the instrument panel; the Chevrolet Body Bank entry clerk tore the label off the bag (which had the key numbers on it) and input those numbers (along with the body number that associated the body to the ident number and dealer order) to the program that generated the Broadcast Copy, which had the key numbers on it when it was printed. When the body got to the Chevrolet Trim Line, the glove box cylinder was installed with the (Chevrolet-painted and assembled) glove box door, and the ignition cylinder was inserted when the steering column was installed. The second set of keys was placed in the ash tray.

Door and quarter panel interior hardware and side glass went in and glass was set to gage blocks on the windshield pillar and roof rail, and roof rail and door opening weatherstrips and drip moldings went in next. After verifying side glass fit, door and quarter trim panels and kickpads were installed. The windshield and backlite glass was cleaned, primed, and had the dam and Thiokol adhesive bead applied, and were installed in the openings, followed by "bear grease" sealer between the bottom edge of the glass and the edge of the opening, and the reveal moldings were installed; the gage-located cowl vent panel was used to locate the ends of the lower windshield reveal moldings, and was left secured by one screw. Taillights, marker lights and emblems were installed (followed by the rear "****tail shakers" on convertibles), sealing fixtures were clamped over the firewall holes, and the body went through a 3-minute water test booth and inspection area. The seats for that car were delivered from the "Cushion Room" where they were built, and the rear carpet and seats were installed last, followed by a final inspection (at Norwood, but not Van Nuys, "P", "T", and "B" ink stamps were applied to the body for Paint, Trim, and Body inspection OK), and the body was shipped up the ramp to Chevrolet.

Chevrolet Assembly Operation Details

Chevrolet Assembly - Body Bank Operations

The trimmed out shells from Fisher were received in a "body bank" on the Chevrolet side. The VIN was assigned in sequential order and the hidden VIN derivatives were stamped on the cowl top and on the dash adjacent to the heater opening. The receiving body bank matched the arriving bodies against customer orders so that the final assembly could be scheduled. Assembly scheduling sorted the units based on equipment and option content to maintain assembly line work station balance. The individual specifications for the remainder of assembly were "broadcast" to assembly stations throughout the Chevrolet assembly plant and the units were released in proper sequence to the Trim Line. Once released from the Body Bank, the assembly sequence was "locked-in" all the way to the end of the Final Line; vehicles could not thereafter be removed from the line.

Order reference: When the body entered the area, the clerk entered the body number from the cowl tag and the newly assigned VIN into the computer, which cross-referenced back to the "ident number" and dealer order number. This data resulted in generation of the precise specifications and all the Chevrolet parts required for that particular car and prepared the file that would generate the "Broadcast Copy" when the car was released.

Scheduling: There were usually six lines in the schedule bank - one for RS, one for A/C, one for SS and Z/28, and three for high-volume standard cars, so cars could be scheduled without having situations like three A/C's in a row, three consoles in a row, three RS's in a row, etc., as these had higher work content vs. the standard cars and scheduling two or three of them in a row would over-cycle certain line operations.

Releasing: When the clerk at the end of the body bank selected the next body based on the scheduling "rules" and released it from its line into the main conveyor to the Trim Line, the computer released the "Broadcast" file with the next sequence number, and it was sent to many teletype printers throughout the plant where subassemblies were built and sequenced for delivery to the Main Line to meet up with that particular car. The same computer program also generated the end-of-line paperwork for that car - the price sticker, car shipper, and other internal documents.

The "Broadcast Copy" (often called the "build sheet" today) included the sequence number, VIN, identification number, dealer code, order number, and selection codes for virtually every part that went on that car. There were two types of Broadcast Copies: the Body Broadcast Copy (BBC) was used on the Trim Line and Final Line, and the Chassis Broadcast Copy (CBC) was used on the Engine Dress, Chassis, and post-marriage overhead Chassis Line. There was some level of duplication on both Broadcast Copies, which were standard Chevrolet forms used in most Chevrolet plants. (Vega assembly at Lordstown was a notable exception - the teletype printers couldn't print a full sheet at 103 per hour, so the Vega Broadcast (designed by yours truly) was only a half-sheet, 8-1/2 by 5-1/2 inches, so the printers could stay ahead of the line.) By the time the car got to the Final Line there were Broadcast Copies all over it, under it, and inside it, as all the various feeder lines used them too. Each installation point for conveyor-delivered components had a trash barrel to pitch the copy that came taped to the subassembly, and there were several at the end of the Final Line.

The car was now officially released for production, and was locked permanently in sequence as it headed for the Trim Line. At Norwood, the body was on a Trim Truck, and at Van Nuys it was in an overhead conveyor clamshell carrier (the low ceilings in the old Norwood Trim Shop building weren't high enough to accommodate overhead conveyors). 

Chevrolet Assembly - Trim Line Operations Details

The Trim Line operations completed mechanical assembly of body-attached components, installed the front end sheet metal, and readied the complete body shell for the chassis-to-body marriage operation on the Final Line.

Completion of Body Trim

The cowl vent panel was removed and placed in the back seat. The VIN plate went in first and the dash mat and upper-level ventilation adapters, ducts, and outlets (or A/C outlets), and the radio speaker and defroster duct went in next, followed by the inside mirror, wiper motor and linkage, washer nozzles and hoses, and cowl vent panel end seals. The A/C air intake plenum valve assembly and A/C vacuum tank followed, and the inside and outside heater or A/C boxes, cables, and control head came next, followed by the A/C inside/outside air valve and cover on the R.H. kickpad. The radio antenna cable was routed and clipped across the lower instrument panel, and the antenna body was taped to the outside of the hinge pillar; rear antenna cars got the hole punched in the quarter panel, and the Fisher-installed cable and antenna body was retrieved from the trunk and assembled to the quarter panel.

Next came the Z87 wood-grain trim plate and assist handle, parking brake bracket, dimmer switch, speedo cable and grommet, accelerator pedal and lever, and the pedal support assembly (and booster with power brakes), plus the clutch pushrod and pushrod seal on manuals, followed by the A/C air distribution and outlet ductwork and the upper instrument panel pad. The instrument cluster was subassembled in an off-line conveyor system, including the instrument panel wiring harness and fuse block, and was installed next, followed by routing the wires, securing the fuse block to the dash panel, and attaching the heater or A/C control head to the cluster. Subsequent operations included the radio, ash tray assembly, and glove box and door, followed by the steering column with the wheel already subassembled to it, then the front carpet and sill plates. Holes were drilled for the console, automatic floor shifter and cable, the riv-nuts were set, and the shifter was installed. The floor console went in next, less the upper trim plate, shift boot, and retainer for manuals, which were installed on the Final Line after Body Drop. The cowl vent panel was retrieved from the back seat, its front seal was added, and it was final-installed on the cowl, followed by the wiper arms and blades.

The rear bumper and guards, RS backup lights, license door and license light were installed, followed by the heater hoses, fuel tank, rear shocks, pinion bumper, and rear spring front U-nuts and rear shackles and upper shackle bushings, and the trim operations were complete.

Front Sheet Metal Installation

Both plants used similar processes for front sheet metal installation. The front sheet metal was "buck-built" as a unit in an off-line subassembly area and installed to the body while the body was still on its Trim Line build truck before the body was picked up by the overhead conveyor carrier that took it to the Final Line.

 

The "buck-built" front clip was lowered into place with an overhead hoist; two operators on each side guided it into position, with the rear two pulling the rear of the fenders outboard to clear the side shroud "saddlebags" on the body as the assembly moved rearward, and the front two guided the radiator support into place on locators at the front of the trim truck. The hook was then released and the hoist went back upstairs to pick up the next assembly. At this point, operator skill became critical as the shim packs were made up and stuffed in place for the top, front, side, and bottom fender-to-body attachments to achieve the correct gap and flush fits between the fenders and the body.

Establishing a perfectly square hood opening was critical, as the hood was "trapped" on all four sides by the header, fenders, and cowl vent grille; a special "hood squaring fixture" was dropped in place. It had two pins at the rear that went into the two holes in the cowl just inboard of the fenders (the ones with the little black plastic plugs in them), two pins at the front that engaged the two holes in the top of the radiator support just inboard of the diagonal brace attachments, and locator blocks on the sides for the fenders. Once the fender fit points at the rear were properly shimmed and secured, the squaring fixture was removed, and the front end was ready for the hood.

The last step prior to hood installation was to retrieve the antenna body from the R.H. hinge pillar and install it to the fender.

Hood Installation

The hinges were fixtured to the fender reinforcement and torqued, and a hood locating fixture was clamped to the top of each hinge; the hood was removed from the delivery conveyor and positioned to the hinges, where the locator fixtures positioned it fore-aft on each hinge, and the bolts were torqued. Final hood fit was established in the next station by two hood fitters who tweaked the hinges, latch, and bumpers to achieve correct gap and flush on all four sides.

From this point, the body was conveyed to the Final Line, where it would meet the chassis.

Chevrolet Assembly - Engine Dress Line Operations Details

The beginning of the engine dress line was a sea of racks full of engines and transmissions; small-block V-8's from Flint V-8 Engine and Tonawanda, big-block V-8's from Tonawanda, and L-6 engines from Flint Motor, plus manual transmissions from Saginaw and Muncie and automatics from Toledo, Cleveland, Warren, and Willow Run.

In the engine schedule area, the operator grabbed the next Broadcast Copy from the printer, verified the sequence number, noted the engine code required for that car, and moved an air-powered overhead hoist on traveling bridge rails over the correct engine rack. The specified engine was hoisted out of the rack and transferred to the next hook on the overhead engine dress line conveyor, where the throwout bearing (on manuals) was greased and installed, along with the clutch fork boot. Another operator on the other side of the line repeated the process with the specified transmission, which was then installed and bolted to the engine; on automatics, an air tool was used to rotate the flexplate, and the converter bolts were driven, followed by the lower cover.

 

The VIN derivative numbers were stamped in the next operation on both the engine pad and the transmission, using a gang-stamp holder and a hammer. From here on, all the detail dress items were added (plug wires, coil, engine harness, battery cables, carburetor, pulleys, alternator, starter, fan and clutch, A/C compressor, power steering pump, transmission cooler lines and fill tube, A.I.R. pump, diverter valve and air manifolds, drive belts, dipstick and tube, oil filter, engine and transmission mounts, PCV plumbing, vacuum fittings, fuel pump and fuel line, radiator hoses, and (if applicable) the transmission-mounted 4-speed manual shifter and linkage was installed and adjusted (3-speed manual floor shifters were mounted on the cross-member and adjusted later on the Chassis line). Engine oil and transmission lube were added, and the completed engine/transmission assembly was conveyed to the Chassis Line for installation in the subframe. The engine line inspector wrote the engine, transmission, and carburetor codes on the Broadcast Copy and put the sheet in a box for pickup by a Scheduling clerk (needed to create the P-O-P at the end of the Final Line).

Chevrolet Assembly - Chassis Line Operations Details

The chassis was subassembled on a steel carrier truck with locators for the subframe, exhaust system and rear axle and springs, which carried the completed chassis to the Final Line for Body Drop.

 

The subframe was built up separately on a feeder line; the bare subframe was loaded on a conveyor, where the frame-side engine mount brackets were installed. Next, the upper and lower control arms and stabilizer bar were loose-installed, followed by the front springs and hub/spindle/brake caliper assemblies. It was then loaded into the "Geo-Machine", which set caster and camber. The machine clamped the subframe down solid against locators, and a swiveling head on each side was bolted to the front hub lug studs; when the machine was cycled, the machine heads compressed the hubs to design suspension height and positioned the wheel mounting face of the hubs to the correct caster and camber angles, which created gaps between the upper control arm shafts and the bracket on the subframe. The operators stuffed both gaps on each side with shims positioned over the studs, and torqued the nuts on both sides and the bushing bolts through the lower control arm bushings, plus the stabilizer bar bushing and end link bolts; the machine then lowered the suspension to full rebound against the upper control arm bumper, the nuts were removed holding the machine heads to the hub faces, and the subframe was transferred out of the machine, flipped upside-down, and the steering gear, pitman arm, idler arm, and steering linkage were installed. The subframe was then flipped right-side-up and loaded on the chassis carrier truck.

The rear axle, rear brake pipes, and rear springs (including the front mounting bracket, bushings, and fully-torqued through-bolt) were subassembled (and the diff lube was added) on another feeder line, and that unit was then loaded on the chassis truck, followed by the front shocks, prop shaft, brake pipes, valves, hoses, and master cylinder, transmission control and backdrive linkage, fuel and vapor lines, and the engine/transmission assembly was installed and all mounts were torqued. The power steering hoses and fuel/vapor lines were connected, the clutch cross shaft was added, 3-speed floor shift linkage was installed and adjusted, and the heat riser valve and complete exhaust system was installed.

The chassis then passed into the fluids area, where the power steering system was evacuated and filled automatically, and the brake system was evacuated-and-filled automatically through the master cylinder - the bleeders on the master cylinder and at each wheel were never touched. Another machine head was then clamped to the back of the master cylinder which pushed on the rear piston to bring the brake system to 1200 psi and held it there for 20 seconds; any pressure decay or movement of the piston indicated a leak. When the leak test was complete, the machine automatically topped-off the fluid level, the test head was removed, and the master cylinder cap was installed. The inspector then wrote the axle number on the Broadcast Copy and set it aside for later pickup by Scheduling, and the complete chassis moved on to the Final Line Body Drop station.

Chevrolet Assembly - Paint Shop Operations Details

The primary function of the Paint Shop on the Chevrolet side of the plant was to paint the front end sheet metal, but there were several other unique paint systems as well that processed many other parts.

Raw Metal: The front fender outer skin and the long inner fender reinforcement were received separately from the stamping plant in order to get more pieces in a standard rack; these two parts were spot-welded together in special fixtures which established the "crown" of the fender so it matched the contour of the hood, and the raw welded assembly was then sent to the primer "Flow-Coat" line.

Sheet Metal Painting: All raw parts (wheels, brackets, etc.) and the front end sheet metal (hoods, fenders, lower fender extensions, header panels, front valances, radiator supports, inner fenders, etc.) went through a cleaning, degreasing, and hot phosphate system, then through a flow-coat booth where it was deluged with black primer from all directions and then baked. The sheet metal parts that got exterior color were pulled off the prime conveyor and loaded on another conveyor buck, in car position, for finish painting; it got a coat of primer-surfacer that was baked and lightly wet-sanded, then got three coats of lacquer, a short bake to "skin" it over, a light wet-sanding and wipe-down, then it went through the final re-flow oven at 275F for 30 minutes. Next was an in-line repair booth where Z-10/Z-11/Z-28 and D-90/DX1 stripe masking, spraying, and de-masking was done (including lower fender blackout when required), followed by another oven. After cooling, the conveyor delivered the buck carrying the color-coated parts, in the same sequence as the cars on the main assembly line, to the sheet metal subassembly area. Exterior color lacquer was supplied by DuPont, and both Fisher Body and Chevrolet Paint Shops at the same assembly location were supplied from the same DuPont-mixed lot in order to minimize any color-match problems. This wasn't an issue at Van Nuys, as their recently-consolidated Paint Shop had each car's front sheet metal on a buck just ahead of the body shell so the entire exterior of the car was painted at the same time with the same paint; that set of sheet metal eventually met up with that same body again after Body Drop on the Final Line.

Wheel Painting: The wheels were removed from the prime conveyor and placed in another conveyor system that took them through a booth where their faces were sprayed with color wheel enamel, then through an oven, and the conveyor continued to the wheel & tire assembly area where the wheels were picked off.

Small Parts Paint: All the miscellaneous brackets and small parts that only got black primer were picked off the prime line after cooling and were placed in individual containers by part number for delivery to the engine, chassis, and final line areas where they were installed.

Low-Bake Paint: Small plastic and metal parts that required color (grilles, consoles, steering columns and covers, N34 steering wheel hubs, ashtray and glove box doors, stereo speaker grilles, etc.) were received in prime from the suppliers and were painted in yet another paint system, in build sequence, baked at 150F in a short infra-red oven, and conveyed to their point of use on the Trim Line and the sheet metal subassembly area.

VE3 Front Bumpers: These optional front bumpers were received already painted from the supplier, as they required a special flexible paint and a unique process not available in the assembly plants.

Final Paint Repair: There were no paint operations of any kind after the finished car came off the Final Line, unless it needed a repair that couldn't be finished in the Paint Shop or if it got scratched during the assembly process after paint. If a spot color repair was required, it was done in an off-line prep area and spray booth with an infra-red oven which only heated the repaired surface to about 150F ("low-bake"), and final gloss of the repaired area was achieved by compounding and polishing.

Chevrolet Assembly - Front Sheet Metal Subassembly

All the color-painted exterior front sheet metal panels, plus the black-primed radiator support, inner fenders, and center grille support and the low-bake painted grille were conveyed to the sheet metal assembly area; all were in "Broadcast" sequence, matching the sequence of bodies on the main assembly line. Option holes for engine emblems, antennas, Vigilite housings, nameplates and moldings were pierced in large hydraulic fender piercing fixtures before the fenders were placed in the assembly fixtures.

The radiator support was built up first and placed on the conveyor fixture, including the radiator, A/C seals, baffles, condenser and plumbing, center grille support, hood latch assembly, horns, header panel, voltage regulator, horn relay, headlights, and RS headlight door assemblies; the lower radiator-to-subframe mount cushions and bolts were installed, retained by zip-nuts so they wouldn't fall off. The seals were stapled to the inner fenders which were then subassembled to the fenders off-line along with the lower fender extensions, A/C dehydrator bottle, Z21 wheel opening moldings, RS vacuum tank, emblems and marker lights, then those fender assemblies were brought to the buck and joined to the header panel and radiator support with the diagonal braces while fixtured at the rear of the buck to establish a perfectly square hood opening. The front valance panel, license plate bracket and parking lights went on, the forward lamp harness and RS vacuum harness was routed and connected to all components, the grille and headlight bezels went on, the washer bottle bracket and battery tray were installed, and the "****tail shakers" were installed on convertibles. The front clip (less the hood) was now ready for assembly to the body at the end of the Trim Line, prior to chassis-to-body marriage.

The hood was hung separately from the conveyor; the pad and latch striker assembly was installed, along with SS louvers and the ZL2 air valve and solenoid assembly, underhood lights, etc.; ZL2 hoods for Z/28's were drilled and had the "302" emblems installed. Hood hinges were installed later on the Trim Line, just prior to hood installation.

Chevrolet Assembly - Final Line Operations

The Final Line is where it all came together, and it was a busy place, with a completed car driven off the line under its own power at one per minute; Final started with off-line operations like the wheel & tire room, and progressed through chassis-to-body marriage, underbody work for brake and fuel line clips, exhaust hangers, parking brake and automatic shift linkage and backdrive linkage adjustment, coolant and A/C fill, console and shift lever completion, car start, air cleaner, price sticker and P-O-P, shipping papers, final inspection, and drive-off into toe-in setting and the roll test.

Wheel And Tire Assembly

Tires were received jammed by the thousands into rail cars, herringbone-style; they were unloaded and hung (in main line car sequence) on a conveyor that took them through a long low-temperature infra-red oven to restore their shape, and were then automatically unloaded directly on the wheel they would be mounted on, which laid flat on a conveyor pallet. The conveyor moved into a mounter, which had moving heads that guided the tire beads over the rim flanges; the conveyor then moved into an inflater, which blew high-pressure air in-between the rim and the tire bead to inflate the tire; the valve stem was never touched. The next station was the balancer, which dropped a glob of hot wax on the tire at the weight location, and the color of the wax denoted the size of the weight required. The weights were applied manually, and the tires were delivered via overhead roller conveyors to the wheel install station on the Final Line after Body Drop.

Pre-Marriage

In this station, the subframe body cushions were installed, engine plumbing and wiring was moved out of the way and placed on top of the engine, the master cylinder was bent forward on its coiled lines, and the steering rag joint was verified in the straight-ahead position.

Chassis-to-Body Marriage

Although dramatic to watch, the chassis-to-body marriage was a pretty straightforward operation, and was done the same way at both plants. At both plants, the traditional "body drop" process was actually a "chassis raise" process, where the complete chassis was raised up into an elevated body shell. It began with the chassis mounted on a waist-height chassis carrier, that was in turn on a pedestal floor conveyor. The body (with the front sheet metal already installed) was suspended in an overhead conveyor carrier about six feet off the floor directly above the chassis carrier. The 0.610-inch diameter gage pins were snapped into place on the No. 2 subframe mounts, and the chassis was raised up to the body by hydraulic cylinders on the chassis carrier; the four subframe-to-body and two subframe-to-radiator support bolts were torqued, the gage pins were removed, the rear springs were secured to the body at both ends, the rear shocks were attached at the spring plates, the exhaust hangers and brake & fuel lines were partially attached, and the chassis carrier dropped back to waist height and returned around its loop to pick up another chassis. The "married" body and chassis continued on down the line suspended in the overhead carrier, six feet off the floor, to finish buttoning-up the underbody, lowered to waist height for wheel & tire installation, and the car was then deposited on its wheels on the dual-strand flat-top Final Line conveyor as the empty overhead conveyor carrier went up an incline and returned to the end of the Trim Line to pick up another body.

Chassis Being Raised into the Body

On the Final Line

Subsequent operations in the Final Line center pit were the same in both plants: the speedo cable was connected, fuel and brake line clips were secured to the underbody, the rest of the exhaust hangers were attached, the main fuel line was attached to the hose from the fuel tank, and the parking brake cables were secured and adjusted. Automatic shift linkage and clutch linkages were adjusted, the backdrive linkage was connected and adjusted, and the convertible floorpan brace was installed.

Up top, the steering column flange was connected to the rag joint, followed by securing the loosely-installed column to the dash and at the toe plate with its trim cover, manual floor shift levers, boots, and retainers were installed along with console trim plates. The master cylinder was pulled rearward and attached to the dash studs or the booster, and final wiring and plumbing connections were made.

Other Operations

The front bumper was installed, radiator and heater hoses and transmission cooler lines were connected, the battery was installed, A/C hoses were connected, and the fan shroud was installed, while the jack and spare tire were secured and wheel covers and floor mats were placed in the trunk. The washer bottle was installed and the washer nozzles were aimed, and both the cooling system and A/C system were evacuated and filled automatically, followed by a pair of operators aiming the headlights; pinstriping fixtures were applied and Z21/D96 pinstripes were painted with Buegler roller-striping guns, and D90 door stripe decals were applied.

 

 

Four or five gallons of gas were pumped into the tank, the carburetor was primed by filling the float bowl through the vent tube, and the car was started for the first time; idle speed was adjusted, automatic transmissions were topped-off, the air cleaner was installed, and the car was ready for drive-off.

The Scheduling clerk had already produced the P-O-P from the Broadcast Copies picked up at the Engine and Chassis lines, the window sticker, car shipper, and final order copy had been produced, and these were placed in the glove box with the warranty folder and owner's manual while the window sticker was applied to the door glass. The car was then "de-papered" by removing all the extra Broadcast Copies, supplier labels, etc. that were taped all over the car as assembly information, and trashing them. Each car and its scheduled subassemblies picked up about twenty Broadcast Copies at it progressed through the Chevrolet assembly system, but it was strictly an internal plant information document and none were shipped with the car's paperwork package to the dealer, although some Van Nuys units had a Broadcast Copy glued to the top of the gas tank.

A team of inspectors gave the car a once-over, and a roll-tester drove the car off the end of the line into the toe-in machine. Here the driver used a fixture that rested on the window opening to hold the steering wheel level while the machine operator in the pit adjusted the tie rod sleeves until toe-in was in spec and tightened the tie rod sleeve clamps. The driver then returned the steering wheel fixture to the pedestal, and drove ahead onto the roll-test machine.

The roll-tester drove the car on the rollers at speeds up to 60 mph or so, checking mechanical operation, instruments, speedometer accuracy (a large master speedometer was suspended overhead in the driver's view), upshifts/downshifts, clutch, brakes, wipers, horn, turn signals, radio, acceleration, A/C operation, and listened for any unusual noises. One side of the rollers was smooth and round, and the other side were eccentric, to mimic driving the car on a rough road - the driver moved the car over to the rough side and listened for any squeaks or rattles, and when the rollers stopped, he drove the car ahead and parked it on another dual-strand flat-top conveyor, noted any discrepancies on the inspection ticket, and returned to pick up another car.

Final Process

The car proceeded down the light repair conveyor to have any minor discrepancies taken care of; for major issues, the car was driven off the end of that line into an off-line repair stall, and was re-roll-tested if necessary to verify the correction. If the car was OK at the end of the light repair line, it went directly to the shipping line. If any paint repair was required, the car went on another short flat-top conveyor that took it through low-bake paint repair, and from there the car went to the shipping line.

 

The shipping line was another flat-top conveyor, which carried the now-finished car "out the door" to the shipping contractor; the car got one more once-over here, and all extraneous labels, stickers, and inspection tickets were removed. At the end of the line, the contractor drove the car away to his shipping yard adjacent to the plant where loads were made up for loading on haulaway trucks or rail cars to begin the journey to the ordering dealer.

Generally, cars to be delivered within several hundred miles of the plant left on haulaway trucks; those destined for dealers further away were shipped by rail, then unloaded at the nearest GM railhead to the dealer and transferred to haulaway trucks for final delivery. Norwood was land-locked and didn't have room for rail loading on-site, so their cars destined for rail shipment had to be driven two miles from the plant to a rail-loading site; the shipper had shuttle buses to bring his drivers back to the plant from the rail yard.

Author Introduction / Biography

(By Rich Fields, CRG Coordinator)
CRG has been fortunate to have John Hinckley as a member for several years. This CRG Research Report by John has been long-awaited by our internal membership, and it is now extensively referenced by Camaro restorers. John's extensive auto industry background includes decades with GM assembly and covered the specific years and locations of first-generation Camaro. He knows the details of 1960's-1970's Fisher Body and Chevrolet assembly processes, tooling, methods, production support systems, and problems. This makes him one of the very few people remaining that is capable of an accurate and detailed first-person account of the complete processes of St.Louis-Corvette, Norwood, Van Nuys, Lordstown, Willow Run, and Flint (among others). John Hinckley lived it, day in and day out, for many years. John's bio includes:

Chrysler 1985-2001: Retired Plant Manager - Conner Avenue Assembly Plant (Viper & Prowler). Chief Engineer - Project Liberty. Chief Engineer - Advanced Process Development. Director - Advanced Manufacturing Engineering.

GM 1964-1985 (Chevrolet and GM Assembly Division): Production, Production Engineering, Vehicle Engineering, Product Promotion Engineering, Process Engineering, Pilot Operations, New Model Pre-Production & Launch.

BSME, Michigan State.

 

-- Edited by 68sd on Tuesday 20th of July 2010 11:34:12 PM