Enjoy 5% OFF at VEVOR Canada! and Support Canadian Poncho at the Same Time!
Members Login
Username 
 
Password 
    Remember Me  
Canadian Poncho Homepage -> Canadian Poncho -> General Acadian/Ventura Discussion -> Connecting mast to antenna body
Post Info TOPIC: Connecting mast to antenna body
canso65


Addicted!

Status: Offline
Posts: 134
Date:
Connecting mast to antenna body
Permalink  

I have the original antenna body from my 65 Acadian. Cowl mount. The antenna was broken off. I see where you can buy just the mast but cant figure for the life of me how to get the remains of the broken one out ando attach a new mast only. Maybe thats not even possible on the old antenna body.

Can anyone confirm one way or the other?



Attachments
__________________
CdnGMfan


Canadian Poncho Superstar!

Status: Offline
Posts: 4956
Date:
Permalink  

I don't remember it causing me too much grief when I replaced my snapped-off mast with the threaded section still in the base. I just grabbed a hand tool and twisted it out.
I replaced it with an NOS GM mast, which later an electrician broke and so was forced again to replace it, this time with a repro.

Hey Canso, are you dealing with a co-ax issue, or is it the mast base itself?

__________________

67 Chevelle Malibu Sport Coupe, Oshawa-built 250 PG never disturbed.

In garage, 296 cid inline six & TH350...

Cam, Toronto.


I don't judge a man by how far he's fallen, but by how far back he bounces - Patton
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
canso65


Addicted!

Status: Offline
Posts: 134
Date:
Permalink  

I think the coax is good. I havent really dug any deeper than the mast. I just dont know if on those original antennas if the mast screws in or not. Do you remember where you bought the mast from? Ive seen a bunch and would like something that looks semi original. 



-- Edited by canso65 on Sunday 18th of February 2024 11:05:11 PM

__________________
canso65


Addicted!

Status: Offline
Posts: 134
Date:
Permalink  

So GMfan, I attached a better picture if my antenna body that shows the mast down inside. That that part remaining be screwed out it maybe thread the new mast into that somehow? Or just get a new body as well?



Attachments
__________________
CdnGMfan


Canadian Poncho Superstar!

Status: Offline
Posts: 4956
Date:
Permalink  

I bought my mast from Heartbeat City Camaro in Michigan as they advertised the mast as 100% authentic. I must admit it looks just like the OEM one.

Although I haven't seen this product or dealt with this vendor, this one looks good: https://www.retromanufacturing.com/en-ca/products/1962-65-chevrolet-chevy-ii-nova-replacement-antenna

It looks like they cover the U.S with dealers but have a single vendor within Canada in Toronto:
Number One Sound
952 College St.
Toronto, Ontario M6H1A5 Canada

Ph: 416-532-6134
Website: Number One Sound

 

I am providing an attachment from my '67 Chevelle Assembly manual that shares the same antenna design, perhaps a minor detail difference in the bezel for your application. The co-ax is supposed to just plug into the bottom of the antenna body until the boot is seated. DO NOT TWIST! It likely will break some of the wire strands or damage the insulation sheath in the co-ax if you do.

67 Chevelle antenna install.jpg



Attachments
__________________

67 Chevelle Malibu Sport Coupe, Oshawa-built 250 PG never disturbed.

In garage, 296 cid inline six & TH350...

Cam, Toronto.


I don't judge a man by how far he's fallen, but by how far back he bounces - Patton
Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.
Canadian Poncho Homepage -> Canadian Poncho -> General Acadian/Ventura Discussion -> Connecting mast to antenna body
Tweet this page Post to Digg Post to Del.icio.us
.
Support Canadian Poncho!
Select Amount:
<
.
.
.