2024 Canadian Poncho Calendars are Now Available! CLICK HERE

 

 

Members Login
Username 
 
Password 
    Remember Me  
Post Info TOPIC: original cast-iron powerglide


Poncho Master!

Status: Offline
Posts: 1921
Date:
original cast-iron powerglide


So i have this nice heavy transmission and it is leaking at the drain plug. So im looking on the net for pans and then realizing as im looking at photos of mine that there is no pan!! The plug is striped and ive tried some thread tape, and some spacers to hope it would catch but its not working. I dont want to drop the tranny yet and the only thing i can think to fix it would be re-tap it, even though i dont have a tap that big(and how do you keep metal shaveings out)  or, weld a nut on there and use another bolt. Any suggestions?  Oh, and i do have a 350 turbo trans here that works, but not sure if it would bolt up right or if i would have to shorten the driveshaft.?

-- Edited by 59poncho at 16:36, 2009-02-08

Attachments
__________________
1959 El Poncho!!


Poncho Master!

Status: Offline
Posts: 1921
Date:

would i have to be fearfull of the trans getting too hot with my wire feed welder? I know to just do little tack welds here and there but would it hurt the tranny junk inside?

__________________
1959 El Poncho!!


Uber Guru

Status: Offline
Posts: 3932
Date:

Try a little silicone around the threads. You would just have to do every oil change. But might keep it from leaking for awile.

Ian

__________________


Uber Guru

Status: Offline
Posts: 3463
Date:

you can buy oil pan oversize/repair plugs at a parts store that might work.
wire feed won't hurt it.
i installed a 350 trans in my '61 impala, in place of a cast iron PG, frt driveshaft needs to be shortened 3"

__________________

 








Uber Guru

Status: Offline
Posts: 3932
Date:

Sorry the silicone advise is lame if you can not even get plug started.

Ian

__________________


Poncho Master!

Status: Offline
Posts: 1921
Date:

thanks guys. I will try the sillicone first and look for the oversize plugs. The trans works fine so i will only replace it if it tinkers out on me. just trying to get these types of things done so im ready for the season. How much would it cost to shorten the small driveshaft?Was yours a column shift car?

__________________
1959 El Poncho!!


Uber Guru

Status: Offline
Posts: 3463
Date:

cost me $125. back in '95 to shorten the frt. and rebalance the complete shaft.
i cut and rewelded the column linkage, used some of the 350 trans linkage to make it all work.

__________________

 








Canadian Poncho Superstar!

Status: Offline
Posts: 6366
Date:

don't be shy, drill it-install a heli coil-wash it through a bit -and fill it back up-if it gets shavings it'll be a while before it goes and you have the turbo 350 for back up

__________________


Canadian Poncho Superstar!

Status: Offline
Posts: 4285
Date:

67BBSD wrote:

don't be shy, drill it-install a heli coil-wash it through a bit -and fill it back up-if it gets shavings it'll be a while before it goes and you have the turbo 350 for back up




Thats what i would do too.
Shavings will flushout easy.
You wont be able to do any welding on it as it is cast IRON.
The th350 swap is easy if you have a V8,  if you have the old 235/261 it won't be fun with adapters and all.



__________________

Beaumontguru

MY BEAUMONT HAS 4 STUDDED TIRES AND 2 BLOCKHEATERS......AND LOTS OF OIL UNDERNEATH.  The other one has a longer roof.



A Poncho Legend!

Status: Offline
Posts: 26765
Date:

Call London Driveline for a quote on the driveshaft Trevor. They do good work and have been around forever.



__________________

Todd
Site Founder

Like us on Facebook. http://www.facebook.com/CanadianPoncho

Canadian Poncho World Headquarters - Prince Edward Island

 

Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.

Tweet this page Post to Digg Post to Del.icio.us
.
Support Canadian Poncho!
Select Amount:
<
.
.
.