Enjoy 5% OFF at VEVOR Canada! and Support Canadian Poncho at the Same Time!
Members Login
Username 
 
Password 
    Remember Me  
Canadian Poncho Homepage -> Canadian Poncho -> General Beaumont Discussion -> New Engine
Post Info TOPIC: New Engine
Yarrowman


Veteran Member

Status: Offline
Posts: 74
Date:
New Engine
Permalink  

Well here it is guys my new 461 ci full roller and gear drive engine! it sounded awesome on the dyno with a nice lumpy idle and blower whine from the gear drive, next week it gets mated to the new TH400 and then dropped into the 69 Custom. More updates as work progresses

Brad



Attachments
__________________

69 Beaumont Big Block Chilliwack, B.C.
SD 396


Poncho Master!

Status: Offline
Posts: 1981
Date:
Permalink  

Eye candy.



__________________
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Beaumont4008


Uber Guru

Status: Offline
Posts: 3935
Date:
Permalink  

Be nice to see that in your car. You still making a SD clone or staying with the Custom look.



__________________
Yarrowman


Veteran Member

Status: Offline
Posts: 74
Date:
Permalink  

I am throwing ideas around...I have the BB hood which is on the car, I have a SD emblem but have not drilled holes (YET) I have been tinkering with the idea of putting on the Tempest CustomS emblem. But I am for sure going with the SD interior cause I just gotta have those stripes!! I am also going with 69 dog dish caps and beauty rings on Wheel Vintiques series 62 wheels for that sleeper look!



__________________

69 Beaumont Big Block Chilliwack, B.C.
rabbit64cs


Canadian Poncho Superstar!

Status: Offline
Posts: 7183
Date:
Permalink  

any numbers from the dyno pull ?  or was it just a break in run?

 

I love it !!



__________________

later...rog

AADD supporting member !!
I'm a collector...not a builder!!Located in sunny central Saskatchewan at the lakehead!
pontorquer


Poncho Master!

Status: Offline
Posts: 2531
Date:
Permalink  

NICE MOTA !



__________________
Yarrowman


Veteran Member

Status: Offline
Posts: 74
Date:
Permalink  

It went to Ricmond engines and they did a cam break in...changed the oil...adjusted the valves and then pulled a dyno run...I built it to be streetable and the numbers were.....

450 HP @ 5500 RPM

501 ft lbs torque @ 3600 Rpm

Should be lots o fun!!!!!



__________________

69 Beaumont Big Block Chilliwack, B.C.
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Stephenzone


Canadian Poncho Superstar!

Status: Offline
Posts: 4771
Date:
Permalink  

brad do you live in yarrow or chilliwhack, or are have they blended into burbs or each other. my pops used to be posted to chilliwack in the late 60's early 70's and he never liked living on base so we rented a house on duncan rd out yarrow way for 1 year in 72, only school i had to wear a uniform was in yarrow. then he bought a house up at cultus lake for 3 years, corner of cedar and sunnyside 72-76. dads old 67 beaumont wagon was bought new in chilliwack. we also live out at cedardale till they built the chem center in vedder crossing (just checked the maps nothing there now). sorry about the ramblings brought back old memories when i saw yarrow in your user name

__________________

sTevE

55 GMC, 70 Pontiac 2+2 rag
Yarrowman


Veteran Member

Status: Offline
Posts: 74
Date:
Permalink  

I live in Yarrow and absolutely love it! quiet or as loud as you want to live!!



__________________

69 Beaumont Big Block Chilliwack, B.C.
LeeRoy


Guru

Status: Offline
Posts: 818
Date:
Permalink  

Yarrowman wrote:

Well here it is guys my new 461 ci full roller and gear drive engine! it sounded awesome on the dyno with a nice lumpy idle and blower whine from the gear drive, next week it gets mated to the new TH400 and then dropped into the 69 Custom. More updates as work progresses

Brad

 My daughter lives up in promontory heights. Maybe I'll hear it from there!

                  Leeroy



__________________
Yarrowman


Veteran Member

Status: Offline
Posts: 74
Date:
Permalink  

Here is a suggestion from Performance Products which is the Cyclone intake manifold on my engine. It has 4 water ports on the intake and I crossed over the back two ports, It is supposed to improve cooling on the #7 & #8 cylinders and balance out the coolant in the engine. I used 300 psi fittings and hose, we'll see how it performs in the coming weeks.

Brad



Attachments
__________________

69 Beaumont Big Block Chilliwack, B.C.
Stephenzone


Canadian Poncho Superstar!

Status: Offline
Posts: 4771
Date:
Permalink  

are those 2 water ports for marine applications?

__________________

sTevE

55 GMC, 70 Pontiac 2+2 rag
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Yarrowman


Veteran Member

Status: Offline
Posts: 74
Date:
Permalink  

I suppose you could use it on a marine engine but this manifold is a direct factory knockoff of the 396/375HP manifold except mine is oval port. The extra water ports are a performance improvement, and it also has nitrous bosses cast into it but they are not drilled.



__________________

69 Beaumont Big Block Chilliwack, B.C.
u2easy


Veteran Member

Status: Offline
Posts: 63
Date:
Permalink  

Very nice!

__________________

64 Beaumont Custom - LS 64

http://www.ls64.net
jim_ss409


Guru

Status: Offline
Posts: 774
Date:
Permalink  

Nice engine! It should be great to drive with all that torque and horsepower so low in the rpm range.

__________________

Barrie Ont.

409 powered 61 Poncho

best time 9.06@ 148 
03cts sport


Uber Guru

Status: Offline
Posts: 3568
Date:
Permalink  

"69 dog dish caps and beauty rings on Wheel Vintiques series 62 wheels "

I love that look. Wondering what wheel width and diameter's you might be going with?...

__________________

"So when you spot violence, or bigotry, or intolerance or fear or just garden-variety hatred or ignorance, just look it in the eye and think... The good outnumber you, and we always will."  Patton Oswalt
Yarrowman


Veteran Member

Status: Offline
Posts: 74
Date:
Permalink  

I cant wait!!!, but at the moment I am changing out the fuel tank, fuel and brake lines and then I will fire her up.....



__________________

69 Beaumont Big Block Chilliwack, B.C.
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Yarrowman


Veteran Member

Status: Offline
Posts: 74
Date:
Permalink  

03cts sport wrote:

"69 dog dish caps and beauty rings on Wheel Vintiques series 62 wheels "

I love that look. Wondering what wheel width and diameter's you might be going with?...

 15"x8"x4.5" offset on the rear and still deciding on how wide to go on the fronts....



__________________

69 Beaumont Big Block Chilliwack, B.C.
seventy2plus2


Canadian Poncho Superstar!

Status: Offline
Posts: 7745
Date:
Permalink  

Yarrowman wrote:

Here is a suggestion from Performance Products which is the Cyclone intake manifold on my engine. It has 4 water ports on the intake and I crossed over the back two ports, It is supposed to improve cooling on the #7 & #8 cylinders and balance out the coolant in the engine. I used 300 psi fittings and hose, we'll see how it performs in the coming weeks.

Brad

This is a very good idea, it'll help move the coolant around.  Your high psi fittings and hose are somewhat overkill, but better safe than sorry.



__________________
70 2+2 convertible
70 2+2 hardtop
70 Parisienne hardtop

 

 
Yarrowman


Veteran Member

Status: Offline
Posts: 74
Date:
Permalink  

seventy2plus2 wrote:
Yarrowman wrote:

Here is a suggestion from Performance Products which is the Cyclone intake manifold on my engine. It has 4 water ports on the intake and I crossed over the back two ports, It is supposed to improve cooling on the #7 & #8 cylinders and balance out the coolant in the engine. I used 300 psi fittings and hose, we'll see how it performs in the coming weeks.

Brad

This is a very good idea, it'll help move the coolant around.  Your high psi fittings and hose are somewhat overkill, but better safe than sorry.

 Thats what I figured....but being how its run behind the distributor I thought I would use these fittings because they are brass and push on...no need for hose clamps...I told the hydraulic guy if they failed he would foot the bill to fix it!!!!



__________________

69 Beaumont Big Block Chilliwack, B.C.
427carl


A Poncho Legend!

Status: Offline
Posts: 35601
Date:
Permalink  

1.JPG

3.JPG

Brad2 (1).JPG

Brad2 (2).JPG

Brad4.JPG



__________________

 
Yarrowman


Veteran Member

Status: Offline
Posts: 74
Date:
Permalink  

Some more pics......just fitting nicely....



Attachments
__________________

69 Beaumont Big Block Chilliwack, B.C.
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Yarrowman


Veteran Member

Status: Offline
Posts: 74
Date:
Permalink  

no tvery good at posting pics!



Attachments
__________________

69 Beaumont Big Block Chilliwack, B.C.
Yarrowman


Veteran Member

Status: Offline
Posts: 74
Date:
Permalink  

gettin the hang of it now........



Attachments
__________________

69 Beaumont Big Block Chilliwack, B.C.
Stephenzone


Canadian Poncho Superstar!

Status: Offline
Posts: 4771
Date:
Permalink  

lookin good

__________________

sTevE

55 GMC, 70 Pontiac 2+2 rag
1 2  >  Last»  | Page of 2  sorted by
 
Quick Reply

Please log in to post quick replies.
Canadian Poncho Homepage -> Canadian Poncho -> General Beaumont Discussion -> New Engine
Tweet this page Post to Digg Post to Del.icio.us
.
Support Canadian Poncho!
Select Amount:
<
.
.
.