Enjoy 5% OFF at VEVOR Canada! and Support Canadian Poncho at the Same Time!
Members Login
Username 
 
Password 
    Remember Me  
Canadian Poncho Homepage -> Canadian Poncho -> Pre 1958 Canadian Pontiac Chassis Forum -> Replacing control-arms bushings??
Post Info TOPIC: Replacing control-arms bushings??
cdnpont


Canadian Poncho Superstar!

Status: Offline
Posts: 10616
Date:
Replacing control-arms bushings??
Permalink  

I always use a heavy threaded rod through the arm and bushing. Some heavy plates either end, a narrow pipe spacer on the far side, and a spilt spacer (2 halves of pipe) in the center like Carl suggests. Lube up the threads, clamp one nut in a vise with the rod facing up and begin cranking down on the other. Keep the bushing aligned to start and it pulls right in no problem.



-- Edited by cdnpont on Thursday 3rd of May 2012 02:52:05 PM

__________________
 67 Grande Parisienne 4 door HT. 69 Parisienne Convertible.
 
57Pontiac


Addicted!

Status: Offline
Posts: 159
Date:
Permalink  

Hi folks,

I am about to re-install the bushings on my control arms and was wondering where / IF I should put grease on the bushing before installing it?

Any tricks from experience on how to press the bushing back in place without the special tools?

 

Thanks!



__________________
Steve
http://57pontiac.biz
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
4SPEED427


A Poncho Legend!

Status: Online
Posts: 50200
Date:
Permalink  

At least a vise, no grease on there, you want it dry and make sure you support the arm so that you don't squish the area closed where you are pressing in the bushing. Also make sure you are pressing only on the outer flange, not the rubber or the centre sleeve.

It will take a pretty good vice to do it. I use our press at work and that goes even better. You might break the vise if it's a cheap Chinese unit.

__________________

1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles 

1966 Grande Parisienne, 396 1 of 23 factory air cars (now converted to a "factory" 4 speed)
4SPEED427


A Poncho Legend!

Status: Online
Posts: 50200
Date:
Permalink  

All good tips Mark. Yes, I should've mentioned, make sure it starts straight!

__________________

1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles 

1966 Grande Parisienne, 396 1 of 23 factory air cars (now converted to a "factory" 4 speed)
seventy2plus2


Canadian Poncho Superstar!

Status: Offline
Posts: 7787
Date:
Permalink  

Would it help to keep the bushings in the freezer overnight?



__________________
70 2+2 convertible
70 2+2 hardtop
70 Parisienne hardtop

 

 
cdnpont


Canadian Poncho Superstar!

Status: Offline
Posts: 10616
Date:
Permalink  

If you're pulling just the rubber or poly into the shell, then freezing them really does seem to help Clint. I did that with the Energy bushings on the 69.



__________________
 67 Grande Parisienne 4 door HT. 69 Parisienne Convertible.
 
57Pontiac


Addicted!

Status: Offline
Posts: 159
Date:
Permalink  

Thanks guys,

Job done. Now I only have to put it back on the car :)

__________________
Steve
http://57pontiac.biz
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
seventy2plus2


Canadian Poncho Superstar!

Status: Offline
Posts: 7787
Date:
Permalink  

photo's please.



__________________
70 2+2 convertible
70 2+2 hardtop
70 Parisienne hardtop

 

 
Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.
Canadian Poncho Homepage -> Canadian Poncho -> Pre 1958 Canadian Pontiac Chassis Forum -> Replacing control-arms bushings??
Tweet this page Post to Digg Post to Del.icio.us
.
Support Canadian Poncho!
Select Amount:
<
.
.
.