Some of you follow my build thread, I never talk about the electric Power Steering system that I sell since 5 years now. I never talk about it because my goal here was to share, and take information, and, I didn't buy one for me since I don't get the car finished.
When I start the car last September I had a steering box issues. Not something important to start a post for. I ask friends if anyone could help me, and I found a great steering column.
The last winter I told to myself it was a good moment to put a electric Power Steering and promote it since, now, I have one in my own car.
I think you would you be interested if I make a How To post about that, and, for the first time, I'll promote the product.
Also, you must think « the system must work on 12 volts, and his car is 6», you're right, but, I built my own system, the Fitzback Garage Smart Charger, and the kit run without changing anything on 6 volts cars. First test year as been made with great success.
Let's get started
Fitz.
-- Edited by Fitz on Sunday 11th of September 2016 07:12:41 PM
__________________
www.FitzbackGarage.com Look for Easy Steering in your vintage Poncho, Look for the EasyDrive Power Steering System in the web site
You don't change suspension geometry, you don't change any steer parts, no alignment needed. You keep the number of steering turn intact. You just get help to turn the wheel, only.
My system in NEW not reman or from junkyard, including electronic. I'm with the manufacturer, the kit is made in France and I imported them directly. NO USED PARTS.
No pump, no hoses, no leaks, no noise.
The system, as pictures will shows, is place between the steering and the gear box. The movement or rotation is sense by a sensor and with the help of a controller, send just enough current to the motor when needed. This motor is connected to a gear, to your steering shaft.
When driving in straight line, everything is shut off. No current demand, no motor idle running.
Fitz.
__________________
www.FitzbackGarage.com Look for Easy Steering in your vintage Poncho, Look for the EasyDrive Power Steering System in the web site
The upper part of the column need to be cut a little bit internally, to fit correctly over the system flange. It's important to do this right now because you'll need a proper fit to keep your total length always accurate. Mostly for your second cut. And fit two set screws to keep it solid on the system.
Since your top tube is fitted on the system, you can measure and cut on the lower side of the column
Fitz
__________________
www.FitzbackGarage.com Look for Easy Steering in your vintage Poncho, Look for the EasyDrive Power Steering System in the web site
It's time to work on the lower parts. In order to bolt the system to the lower tube, I choose to be more strong than weak. I welded a plate as straight as possible at the top of the lower tube. Before that, I need to disassemble the gear box to make room for the machining a little bit later. I shave the plate to put it 90° straight with the tube and the system. I need room also for the center hole.
ATTENTION: you can use another route, lighter if you want by using the center shaft as a guide for welding a plate. Since welding can make your parts moving and make your kit not aligned correctly after, so I choose a safer way.
__________________
www.FitzbackGarage.com Look for Easy Steering in your vintage Poncho, Look for the EasyDrive Power Steering System in the web site
The threaded upper shifter support has to be cut just a little bit to be installed by the interior of the car. It will be easier that way for the installation.
Fitz.
__________________
www.FitzbackGarage.com Look for Easy Steering in your vintage Poncho, Look for the EasyDrive Power Steering System in the web site
Like said before, the system work on 12 and my car is on 6 volts. I run the car all the summer with the Smart Charger and it work great!
The system got a potentiometer to ajust the «torque» needed or for the driver feeling.
I found that the maximum position for the easiest driving steering feeling is too high. It's like turning the steering on a shaft and bearing, nothing at the other end. Standstill it's harder a little bit than driving on the road but, it's a huge improvement. You can go backward twist your back and head and turn the steering with one finger!!
The system is not separated from the IN and the OUT shaft, so if a problem occur, or a lack of battery you're safe, the car will go back like it was before, hard to turn. No differences!
The system need .5-.8 amps while running in straight line, for correction. On stop, it need .1 amp.
On a turn, car in motion, 3-5 amps it needed, for approx. 10-15 seconds.
Stand still with the Pontiac, 45 amps is necessary to turn the wheels, on bad pavement (where I was for the test).
The device can put in the small battery 2-2.5 amps if the battery is at a good level. If the battery get low, it will automatically get higher to 4-4.5 amps maxi.
The voltage stay between 13.5 and 14.4. Since most of the time, the car go in straight line, the device will keep the small battery in full state of charge, and no electrical modification to the car. A connector can be added to charge cell phone etc.
The device is design specifically for that power steering purpose, with a built in 30 seconds -ON- delay timer. This characteristic won't interfere with the ignition while starting the engine.
Fitz.
__________________
www.FitzbackGarage.com Look for Easy Steering in your vintage Poncho, Look for the EasyDrive Power Steering System in the web site
Wow, now that is really something. I am going to remember this for possible future use on a car. What would the cost be for the complete unit/kit, if a person installs it themselves. Thanks for sharing.
__________________
1957 Pontiac Pathfinder Deluxe sedan restored 261 six
1974 Chevrolet Caprice Estate wagon low mileage original 400 V-8
You are a genius Andre'! I love seeing all your work!
__________________
Prince Edward Island
'64 Parisienne CS "barn find" - last on the road in '86 ... Owner Protection Plan booklet, original paint, original near-mint aqua interior, original aqua GM floor mats, original 283, factory posi, and original rust.
Fitz is too humble. I caught part 2 of the article on his Pontiac in the last Hemmings Classic Car magazine (yes, his feature took two issues!). Incredible what you did to adapt that frame Fitz! True genius!
Fitz is too humble. I caught part 2 of the article on his Pontiac in the last Hemmings Classic Car magazine (yes, his feature took two issues!). Incredible what you did to adapt that frame Fitz! True genius!
See, I said he was a genius!
__________________
Prince Edward Island
'64 Parisienne CS "barn find" - last on the road in '86 ... Owner Protection Plan booklet, original paint, original near-mint aqua interior, original aqua GM floor mats, original 283, factory posi, and original rust.