Enjoy 5% OFF at VEVOR Canada! and Support Canadian Poncho at the Same Time!
Members Login
Username 
 
Password 
    Remember Me  
Canadian Poncho Homepage -> Canadian Poncho -> Acadian/Ventura Power Train Tech Forum -> Removing clutch pilot bushing
Post Info TOPIC: Removing clutch pilot bushing
4SPEED427


A Poncho Legend!

Status: Online
Posts: 50198
Date:
Removing clutch pilot bushing
Permalink  

Since this is a tech topic I wanted to put it in tech forum.

Just a reminder or a tip if you happen to have never heard it. I was again today reminded how slick this tip is.

I removed the pilot bushing from a crank using an old Muncie four speed input shaft and a bunch of grease. Filled the cavity with grease, tapped the input snout in until it bottomed on the bushing, filled the cavity with grease again, tapped the input and out it came. It took me far longer to type this than to do it, maybe 1 minute total. So slick!!!

__________________

1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles 

1966 Grande Parisienne, 396 1 of 23 factory air cars (now converted to a "factory" 4 speed)
Beaumont4008


Uber Guru

Status: Offline
Posts: 3936
Date:
Permalink  

Great tip, I have one to take out. Will give it a try.

__________________
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
4SPEED427


A Poncho Legend!

Status: Online
Posts: 50198
Date:
Permalink  

Just make sure you fill it right full to start, and you have to fill it up again once the bushing comes part way out. It loses the hydraulic advantage as the grease is trying to fill a larger void than you start with.

__________________

1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles 

1966 Grande Parisienne, 396 1 of 23 factory air cars (now converted to a "factory" 4 speed)
Stephenzone


Canadian Poncho Superstar!

Status: Offline
Posts: 4771
Date:
Permalink  

i've always taken them out that way

__________________

sTevE

55 GMC, 70 Pontiac 2+2 rag
Ghost Post


Poncho Master!

Status: Offline
Posts: 1628
Date:
Permalink  

Stephenzone wrote:

i've always taken them out that way

Me too!.
Wish the roller ones were as easy and reusable too..

smile.gif

 



__________________

 

 

I like real cars best...especially the REAL real ones!
----------------------------------------------------------------
-Robert M-


Addicted!

Status: Offline
Posts: 286
Date:
RE: Removing clutch pilot bushing THANKS
Permalink  

Just a heartfelt word of thanks. In the midst of putting clutch kit into 59. 

Was wrestlng with bushing for hours - the removal kit slide hammer thingy I bought failed miserably.

Admittedly, I had seen this method on YouTube but dismissed  as, invariably, it was with a two year old Subaru or Honda and some looked downright staged.

Read Carls post and realized it had been done with one of our relics so must be something to it.

15 minutes, out it came.

 

BIG thank you...

 

RGM

 



__________________

1959 Pontiac Laurentian - 1956 MG Magnette ZA - 1962 Dodge Dart 440 - 1962 Hillman Minx - 1977 Ford LTD Landau - 2017 Ford Fusion Platinum - 1963 Imperial Crown- 2008 Sebring  Convertible 

www.everythingelectronic.ca
seventy2plus2


Canadian Poncho Superstar!

Status: Offline
Posts: 7787
Date:
Removing clutch pilot bushing
Permalink  

Yup, people have been using this method for decades. Glad it worked for you.

__________________
70 2+2 convertible
70 2+2 hardtop
70 Parisienne hardtop

 

 
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
4SPEED427


A Poncho Legend!

Status: Online
Posts: 50198
Date:
Permalink  

It makes sense when you think about it, but I still find it amazing!

I see guys using pilot bushing pullers and I think "why"? This is fast, simple and cheap.

__________________

1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles 

1966 Grande Parisienne, 396 1 of 23 factory air cars (now converted to a "factory" 4 speed)
JC2+2


Poncho Master!

Status: Offline
Posts: 1767
Date:
Permalink  

Here's a faster and easier way yet. As long as it's a brass bushing take a large enough tap (5/8" if I remember correctly) and run the tap into the bushing and keep going after it bottoms out. Pushes the bushing right out. If you use an air ratchet to drive the tap, takes about 10 seconds. If it's a bearing wrap electrical tape around a shaft and use the grease trick. Helps to seal in the grease.

__________________

'68 Parisienne 2+2 Convertible Matador Red (Resale Red but not for sale).
4SPEED427


A Poncho Legend!

Status: Online
Posts: 50198
Date:
Permalink  

I didn't have much trouble with grease leaking out the shaft but maybe the bearing was in pretty nice shape too.

__________________

1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles 

1966 Grande Parisienne, 396 1 of 23 factory air cars (now converted to a "factory" 4 speed)
57 Pathfinder


Guru

Status: Offline
Posts: 597
Date:
Permalink  

The tap works better for not shooting grease back at your face...lol

__________________
4SPEED427


A Poncho Legend!

Status: Online
Posts: 50198
Date:
Permalink  

But what to you do with dry skin issues then?

__________________

1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles 

1966 Grande Parisienne, 396 1 of 23 factory air cars (now converted to a "factory" 4 speed)
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Fake68


Guru

Status: Offline
Posts: 671
Date:
Permalink  

filling it up with wadded up wet paper also works. I had a roller bushing I could not get out with grease and the paper worked no problem... It doesn't squirt out as bad and WAY less messy.

__________________

72 Nova SS - Minitubbed
70 Nova SS - #'s L-78 Bench Stick
68 Acadian SS clone - factory air
67 Chevelle rag - SS 427 clone

4SPEED427


A Poncho Legend!

Status: Online
Posts: 50198
Date:
Permalink  

Just some paper towel or something, soaking wet? Never would have thought of that.

Takes an engineer to figure that one out.......!

__________________

1966 Strato Chief 2 door, 427 4 speed, 45,000 original miles 

1966 Grande Parisienne, 396 1 of 23 factory air cars (now converted to a "factory" 4 speed)
Fake68


Guru

Status: Offline
Posts: 671
Date:
Permalink  

Just like spitballs !!
I can't take credit for the idea but it works !

__________________

72 Nova SS - Minitubbed
70 Nova SS - #'s L-78 Bench Stick
68 Acadian SS clone - factory air
67 Chevelle rag - SS 427 clone

Turtle


Addicted!

Status: Offline
Posts: 147
Date:
Permalink  

I used the big end of a 3/8 drive extension with a little electrical tape wrapped around the end for a tight fit. Filled cavity with grease and popped it out with a couple of taps.

__________________

63 Acadian Invader 4dr *SOLD*

63 Acadian Sport Deluxe Coupe

63 Acadian Sport Deluxe Convertible

2007 Pontiac G6 Convertible

99 Silverado Z71

2011 HHR LT
pontiax


Poncho Master!

Status: Online
Posts: 1461
Date:
Permalink  

1A141F66-30A6-462E-9159-06DAE695D31F.jpeg



Attachments
__________________

pontiax- (canadian pontiac X frame)1964 Parisienne 2dr. Hardtop ,lagoon aqua metallic (Q) ,421 cid Dart Industries block and heads. 550 hp. 575 ft lb  of torque.

 
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
Prefectca


Poncho Master!

Status: Offline
Posts: 1758
Date:
Permalink  

I have always used the grease method to remove the bronze bushings. The reason being that I can reuse it in the replacement engine. Back in the eighties new ones were about two bucks, but that didnt help when they were out of stock!

Paul

__________________
Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.
Canadian Poncho Homepage -> Canadian Poncho -> Acadian/Ventura Power Train Tech Forum -> Removing clutch pilot bushing
Tweet this page Post to Digg Post to Del.icio.us
.
Support Canadian Poncho!
Select Amount:
<
.
.
.