Canadian Poncho

Anyone have a junk car with a power window harness in it that is cut up/junk/for parts? I need to find a connector that fits on the back of the master switch (4 button) for the power windows. It should be the same from the early 60's right into the mid/later 70's I think. I need that connector on the back of th...

I need a single groove crankshaft pulley from a 65-67 396 or 427. I bought a used one but when I checked it over I see it's cracked around one bolt hole on both sides of the hole as well as bent, so I don't think I can use it. The correct one may have 3874412 on it. It's a single groove, sits right tight to the bala...

Desperately seeking a right hand rear window trim corner. 2 door sedan 65 and 66 for sure. Maybe 67-68. Possibly 4 door sedan as well? Super hard to find as the sun basically consumed these pieces. Not reproduced, only the sides and tops and the connecting clip are. If I could somehow, I would get them re...

About a year ago, I was able to get a standard front stabilizer bar with all the fixins' from good member Greg (SGS Welding), thanks again Greg, amazing condition after I unwrapped it from it's hermetic sealing! Doesn't even need paint! I think it was from his 67, and it's obvious the 67 brackets are dif...

The rearview mirror in my 65, while in decent shape as far as the silvering goes, will not hold the night position no how. It always pops back up to daytime and there appears no way to open it to tighten that position detent. Do you know how? Normally, It wouldn't be a problem, but for some reason, in the 65 a...

	Forum	Replies	Views	Last Post
FOUND! Power window connector wanted (Preview)	Canadian Pontiac/Acadian/Beaumont Cars/Parts Wanted	4	973	Feb 15, 2012 by 65wagon
Anyone have a junk car with a power window harness in it that is cut up/junk/for parts? I need to find a connector that fits on the back of the master switch (4 button) for the power windows. It should be the same from the early 60's right into the mid/later 70's I think. I need that connector on the back of th...
FOUND! 396 or 427 crank pulley wanted (Preview)	Canadian Pontiac/Acadian/Beaumont Cars/Parts Wanted	10	1422	Mar 18, 2012 by 4SPEED427
I need a single groove crankshaft pulley from a 65-67 396 or 427. I bought a used one but when I checked it over I see it's cracked around one bolt hole on both sides of the hole as well as bent, so I don't think I can use it. The correct one may have 3874412 on it. It's a single groove, sits right tight to the bala...
FOUND! 65-68? Rear window, inside corner trim wanted. (Preview)	Canadian Pontiac/Acadian/Beaumont Cars/Parts Wanted	22	1205	May 6, 2021 by 4SPEED427
Desperately seeking a right hand rear window trim corner. 2 door sedan 65 and 66 for sure. Maybe 67-68. Possibly 4 door sedan as well? Super hard to find as the sun basically consumed these pieces. Not reproduced, only the sides and tops and the connecting clip are. If I could somehow, I would get them re...
found! Looking for a pair of 1965 B front stabilizer bar brackets. (Preview)	Canadian Pontiac/Acadian/Beaumont Cars/Parts Wanted	5	982	Jun 1, 2020 by a421cat
About a year ago, I was able to get a standard front stabilizer bar with all the fixins' from good member Greg (SGS Welding), thanks again Greg, amazing condition after I unwrapped it from it's hermetic sealing! Doesn't even need paint! I think it was from his 67, and it's obvious the 67 brackets are dif...
FOUND! Looking for a 65 big car rearview mirror. (Preview)	Canadian Pontiac/Acadian/Beaumont Cars/Parts Wanted	14	1083	Sep 22, 2022 by Greaser
The rearview mirror in my 65, while in decent shape as far as the silvering goes, will not hold the night position no how. It always pops back up to daytime and there appears no way to open it to tighten that position detent. Do you know how? Normally, It wouldn't be a problem, but for some reason, in the 65 a...