65-70 Full Size Body Tech Forum

Bago · Bago

Hey, does anyone know where I can get these clips from (see pic). It's to attached the stainless lower trim to the body that fits on above the scuttle panel (the one that houses the wipers ((see pic)) Thanks Ian

muttwood · muttwood

http://replica-plastics.com/EditParts.aspx?Make=Pontiac

willard · willard

on the 1969 pontiac parisienne 2+2 the moulding that is about 4 inchs from the bottom of the car is it a chome moulding or is it a stripe thanks willy

4SPEED427 · 4SPEED427

I bought the centre section of the trunk pan to put into my GP. The only are I really need is the little well for the spare tire and a couple of inches around it, but the least you can buy is the centre strip from front to back. I trimmed it down quite a bit, this is still more than I need. Anyway, nice solid piece...

koolconvertible · koolconvertible

does anyone repro the small convertible door jam rub plates and strike plates?

koolconvertible · koolconvertible

can one of you fine peeps be able to supply a pic of what the factory brackets look like which the fender skirt tags fit into on the body for a 65 full size? or do they not have any?we don't see them on Oz cars but I am sure they exist. they fit ok but must rely on hooking around the fender inner lip. I may have to ma...

4SPEED427 · 4SPEED427

Rather than step on toes and derail the other thread about power window motor replacement, I thought I'd start fresh. Not too much to show so far. Today I drilled the one hole that needs drilled to do this, and punched out the two factory plugs that are all set up for the conversion. On the left is the one th...

Hardtail · Hardtail

Hi guys, My car is faded so I am not sure how it was supposed to look stock and I have never seen one of these in person. I know this is a different model but, is the main line on cdnpont's car here going to be the same on my 66? thanks

427carl · 427carl

My 66 project car needs rear body mount bushing(s) for Safety in On The mounts are sitting on 2 rusty panels Carl 1 refered me to the correct panels My car had a previous repair over top of the panels for the bushings.. Friday night I drilled and loosened the mounts underneath Saturday night...

turk · turk

Hi, can anybody tell me where I can get new window felts for my 1965 Pontiac Parisienne Custom Sport. they have a small strip of chrome on them. Thanks for the help and your time -- Edited by turk on Tuesday 14th of October 2014 03:26:37 PM

Rael Fisher · Rael Fisher

Hi, I have a 1965 Parisienne Convertible, and am hoping that someone may know where I can get replacement sheet metal for inner fenders, all wheel arches, and floor pans? Or if anyone knows what other cars parts would fit, I've heard impala or Bonneville may work? Thanks.

hotrodrally · hotrodrally

I'm looking for a hood spear in good condition for my 66 Acadian. Let me know if you have one your willing to part with.

koolconvertible · koolconvertible

does the large chrome headlight bezel have a gasket of some description between it and the fender?

Brad047 · Brad047

So here is my problem I have not front signal lights no wires running to the front where they might be so I have no clue where they should be, but then again it has had no seat belts for the past 14 year too.On a different note is there some where I should add my cowl tag to here. Sorry about the grammer .

73SC · 73SC

Picked these up today and I don't really recognize what year model it came from. Can anyone help?

427carl · 427carl

With pictures and article supplied from Carl 1 (Western Carl) I ordered a "new made in Canada" Spectra GM37"K" tank GM37C is for Impala $299.95 trade price plus tax from Car Quest ($199.95 from E-bay with no shipping no tax) Since Carl sprayed his with clear finish... ...

normffff · normffff

does anybody know if canadian station wagon rear bumpers are the same as us pontiacs...could use one for my 66

cdnpont · cdnpont

I've had a new limited slip decal like this kicking around for years, and now I can actually place it on the inside of the trunklid! Where on the lid would the factory have likely placed it? Would our Canadian Pontiac big cars actually have had this Decal?

4SPEED427 · 4SPEED427

I know the inside of the trunks in 66 is supposed to be body colour. Can anyone confirm exactly what gloss it should be? Is it the same as the exterior paint? Somehow, in the back of my mind it seems to me that it's more of a semi gloss. I would assume it's the same for Beaumonts and Acadians of the same year, so...

4SPEED427 · 4SPEED427

[URL=http://s743.photobucket.com/user/lottapics/media/66%20GP/DSCF0418_zpsfdc3210a.jpg.html][IMG]https://i743.photobucket.com/albums/...

Topic		Started By	Replies	Views	Last Post
	Windscreen trim clips (Preview) Hey, does anyone know where I can get these clips from (see pic). It's to attached the stainless lower trim to the body that fits on above the scuttle panel (the one that houses the wipers ((see pic)) Thanks Ian	Bago	5	946	Jan 13, 2015 by koolconvertible
	Replica Plastics, Anybody ever deal with them ? (Preview) http://replica-plastics.com/EditParts.aspx?Make=Pontiac	muttwood	1	735	Dec 26, 2014 by 73SC
	1969 parisienne 2+2 (Preview) on the 1969 pontiac parisienne 2+2 the moulding that is about 4 inchs from the bottom of the car is it a chome moulding or is it a stripe thanks willy	willard	6	1090	Dec 18, 2014 by Leo2+2
	Review of a repro part --- Goodmark trunk pan (Preview) I bought the centre section of the trunk pan to put into my GP. The only are I really need is the little well for the spare tire and a couple of inches around it, but the least you can buy is the centre strip from front to back. I trimmed it down quite a bit, this is still more than I need. Anyway, nice solid piece...	4SPEED427	16	2416	Dec 14, 2014 by norontcan
	convertible door rub plates (Preview) does anyone repro the small convertible door jam rub plates and strike plates?	koolconvertible	14	944	Dec 4, 2014 by koolconvertible
	fender skirt (or spats as we call them in Oz) body brackets (Preview) can one of you fine peeps be able to supply a pic of what the factory brackets look like which the fender skirt tags fit into on the body for a 65 full size? or do they not have any?we don't see them on Oz cars but I am sure they exist. they fit ok but must rely on hooking around the fender inner lip. I may have to ma...	koolconvertible	1	543	Dec 4, 2014 by Budgie
	Power window, power vent, power lock conversion ( 1 2 ) (Preview) Rather than step on toes and derail the other thread about power window motor replacement, I thought I'd start fresh. Not too much to show so far. Today I drilled the one hole that needs drilled to do this, and punched out the two factory plugs that are all set up for the conversion. On the left is the one th...	4SPEED427	43	4084	Dec 3, 2014 by 4SPEED427

	Is the main body line on the '66 Grande Parisienne Sharp? (Preview) Hi guys, My car is faded so I am not sure how it was supposed to look stock and I have never seen one of these in person. I know this is a different model but, is the main line on cdnpont's car here going to be the same on my 66? thanks	Hardtail	5	848	Nov 20, 2014 by 58 poncho fan
	66 B-Body rear body mount panel replacement ( 1 2 ) (Preview) My 66 project car needs rear body mount bushing(s) for Safety in On The mounts are sitting on 2 rusty panels Carl 1 refered me to the correct panels My car had a previous repair over top of the panels for the bushings.. Friday night I drilled and loosened the mounts underneath Saturday night...	427carl	32	3759	Oct 19, 2014 by NOS
	1965 Pontiac Parisienne Custom Sport Window Felts (Preview) Hi, can anybody tell me where I can get new window felts for my 1965 Pontiac Parisienne Custom Sport. they have a small strip of chrome on them. Thanks for the help and your time -- Edited by turk on Tuesday 14th of October 2014 03:26:37 PM	turk	8	1224	Oct 15, 2014 by turk
	sheet metal wanted (Preview) Hi, I have a 1965 Parisienne Convertible, and am hoping that someone may know where I can get replacement sheet metal for inner fenders, all wheel arches, and floor pans? Or if anyone knows what other cars parts would fit, I've heard impala or Bonneville may work? Thanks.	Rael Fisher	5	934	Sep 29, 2014 by Rael Fisher
	Wanted hood spear 66/77 Acadian (Preview) I'm looking for a hood spear in good condition for my 66 Acadian. Let me know if you have one your willing to part with.	hotrodrally	0	401	Sep 19, 2014 by hotrodrally
	65 parisienne headlight surround/bezel (Preview) does the large chrome headlight bezel have a gasket of some description between it and the fender?	koolconvertible	1	658	Sep 15, 2014 by Budgie
	1967 Parisienne front turn signal lenses (Preview) So here is my problem I have not front signal lights no wires running to the front where they might be so I have no clue where they should be, but then again it has had no seat belts for the past 14 year too.On a different note is there some where I should add my cowl tag to here. Sorry about the grammer .	Brad047	2	725	Sep 9, 2014 by Leo2+2

	Need help Identifying 396 emblem (Preview) Picked these up today and I don't really recognize what year model it came from. Can anyone help?	73SC	8	878	Aug 31, 2014 by 73SC
	A tankless job (Preview) With pictures and article supplied from Carl 1 (Western Carl) I ordered a "new made in Canada" Spectra GM37"K" tank GM37C is for Impala $299.95 trade price plus tax from Car Quest ($199.95 from E-bay with no shipping no tax) Since Carl sprayed his with clear finish... ...	427carl	7	927	Aug 20, 2014 by 427carl
	66 wagon rear bumpers (Preview) does anybody know if canadian station wagon rear bumpers are the same as us pontiacs...could use one for my 66	normffff	15	1241	Aug 14, 2014 by normffff
	Limited slip decal, where should it go? (Preview) I've had a new limited slip decal like this kicking around for years, and now I can actually place it on the inside of the trunklid! Where on the lid would the factory have likely placed it? Would our Canadian Pontiac big cars actually have had this Decal?	cdnpont	7	742	Aug 4, 2014 by Beaumont4008
	66 Pontiac trunk paint (Preview) I know the inside of the trunks in 66 is supposed to be body colour. Can anyone confirm exactly what gloss it should be? Is it the same as the exterior paint? Somehow, in the back of my mind it seems to me that it's more of a semi gloss. I would assume it's the same for Beaumonts and Acadians of the same year, so...	4SPEED427	13	1250	Aug 3, 2014 by jmont64
	New Canadian made fuel tank for 1966 ( 1 2 ) (Preview) [URL=http://s743.photobucket.com/user/lottapics/media/66%20GP/DSCF0418_zpsfdc3210a.jpg.html][IMG]https://i743.photobucket.com/albums/...	4SPEED427	28	2868	Jul 8, 2014 by 4SPEED427
«First < 1 … 12 13 14 15 16 … 26 > Last» \| Page of 26 sorted by