65-70 Full Size Body Tech Forum

hoosier235 · hoosier235

hello does any body know if 1965 pontiac parisenne sport 2 door quarter panals line up on a 1966 pontiac parisenne two door hard top and if body lines are the same? -- Edited by hoosier235 on Monday 27th of May 2013 09:10:13 PM

SGS Welding · SGS Welding

1967 pontiac parisienne convertable is leaking fluid in or around the driver side cylinder. were do I start ? top closed remove rear seat remove trim does that get me close? Is there a better way to approach this? Have never had a convertable not sure where to start Thanks Greg

68 427 · 68 427

TOOK THE 2+2 OUT OF HIBERNATION YESTERDAY. THE LEFT SIGNAL LIGHT DOES NOT FLASH. IT COMES ON AND CANCELS BUT DOES NOT BLINK. THE RIGHT STILL BLINKS. WOULD THAT BE THE FLASHER, I ALWAYS ASSUMED WHEN THEY WENT BAD, BOTH QUIT BLINKING. AM I WRONG?

JC2+2 · JC2+2

I recently replaced the front springs in my '68 2+2 and then checked the ride height. I then noticed the LR was lower than the RR at the wheel opening. There was some body repair done so I remeasured at the body line ( 1/2" lower ). I measured the actual ride height ( frame to diff tube ) and they are equa...

normffff · normffff

ive got some seriously rusty spots on my 'new' 66 strato chief wagon and wondering if theres any good pieces out there...its the area behind the front wheel wells and all around the rear wheel wells and all the way back to the bumper...thanks

Bud Dewson · Bud Dewson

Does anybody know where i can get replacement front fender Stratochief emblems or someone who restores them?

Blackheart4355 · Blackheart4355

Well, I purchased a set of clear Impala front turn signal lenses, thinking they were the correct ones. They were not, looking further into it...it looks like 1967 Firebird lenses are the same...can anyone confirm this? thanks...

Bago · Bago

Hey there, my hood is stuck down on my '67 Parisienne, any one know how best to release it? Thanks Ian

4SPEED427 · 4SPEED427

I installed the Metro door weatherstrips on my GP this afternoon, for obvious reasons as the pic shows (my old pieces, brittle, torn, missing etc). No photo shoot cause it's really a simple job with one exception. What have you guys used to push those retaining pins into the holes in the door??? I used m...

lofty · lofty

Hi, does any one know if the lower cowl panel for a 67 chev Impala will fit my 67 parisienne? They look the same and mine is rusted out and needs repairing. I found this repo one for an impala.

GrtDanes · GrtDanes

Hi boys I have a chance to buy a complete body with all the parts except motor and frame.Just woundering if its worth my time to buy it and part it out?Its already disasembled. Any comments would be helpful,going to see it tomorrow.It is a sweet deal.

4SPEED427 · 4SPEED427

And I don't mean Tylenol either! We haven't talked about T3's forever, so........ I bought Wagner halogens today for my black GP. I'm not surprised to see that even a company with such a good reputation for quality sells me seal beams that had a boat ride to Canada. Oh well, I guess it's to be expected. An...

4SPEED427 · 4SPEED427

I just thought I'd mention that anyone with a 66 B body (and likely lots of other Pontiacs use the same number) can still buy brand new rubber door bumpers from their local GM dealer. I didn't bring the part number home with me but I got new ones for my car this week. My old ones were either gone or pretty ratt...

4SPEED427 · 4SPEED427

There has been some discussion on here in the past regarding fuel tank interchange between 65-66 Canadian Pontiac and 65-66 Chevrolet. My memory says it's never been proven they interchange, and searching old threads on this site, I can't prove it either. So, the million dollar question. Has anyon...

4SPEED427 · 4SPEED427

I know one of you two guys can answer my question. I am installing a vacuum reservoir for my power trunk. I pulled two out of my US GP parts car. One is very tiny, about 3" diameter, 4" tall. One is about 7" diameter, 8" tall. I am thinking one of these is for the vacuum trunk, one is for t...

norontcan · norontcan

Wondering if a 65 Parisienne Custom Sport grille bezel is the same as a 65 Grand Prix. Might the Grand Prix have an extra mounting hole for the fog light? I only have the Cdn book and took these numbers from it: 9779160 (right) and 9779161 (left ) grille bezel, 5739086 grille radiator Might anyone be able...

4SPEED427 · 4SPEED427

I may have asked this before but I searched and can't find it, if so. In the not too distant future I need to reinstall the rear glass in my GP. I am going to use urethane and need some of those little rubber blocks to keep the glass from sliding down while the urethane cures. I can't seem to find them. Any idea...

4SPEED427 · 4SPEED427

Has anyone used a B body Metro trunk weatherstrip? If so, how is it? I tried mine. It fits the channel very nicely, and it seems to work ok closing the trunk, but the profile sure is a lot different than the original. I had a Soffseal piece years ago on my Acadian and it never let the trunk lid sit down properl...

4SPEED427 · 4SPEED427

It seems to me that Ken posted up about his experience installing his window seals after his car was painted. I can't find that thread to add my own experience to it, so I'll start another one with apologies if there happens to be some overlap. I also know I posted a link on how to do this, from another forum...

RogerB · RogerB

I am in the process of transforming my 68 Parisienne in a 2+2.The interior is mostly done. I found the loovers of the front fenders and the 2+2 emblems for the rear quarter panel. Does someone have the measurements for the 16 holes securing the loovers and the same for the 2+2 emblem? ( where to punch the...

Topic		Started By	Replies	Views	Last Post
	quarter panals (Preview) hello does any body know if 1965 pontiac parisenne sport 2 door quarter panals line up on a 1966 pontiac parisenne two door hard top and if body lines are the same? -- Edited by hoosier235 on Monday 27th of May 2013 09:10:13 PM	hoosier235	14	1679	Jun 3, 2014 by luppy
	Leaking hydraulics for convertable power top (Preview) 1967 pontiac parisienne convertable is leaking fluid in or around the driver side cylinder. were do I start ? top closed remove rear seat remove trim does that get me close? Is there a better way to approach this? Have never had a convertable not sure where to start Thanks Greg	SGS Welding	16	1014	Jun 2, 2014 by Lefty
	1969 SIGNAL LIGHT (Preview) TOOK THE 2+2 OUT OF HIBERNATION YESTERDAY. THE LEFT SIGNAL LIGHT DOES NOT FLASH. IT COMES ON AND CANCELS BUT DOES NOT BLINK. THE RIGHT STILL BLINKS. WOULD THAT BE THE FLASHER, I ALWAYS ASSUMED WHEN THEY WENT BAD, BOTH QUIT BLINKING. AM I WRONG?	68 427	3	564	May 26, 2014 by seventy2plus2
	Rear body uneven. (Preview) I recently replaced the front springs in my '68 2+2 and then checked the ride height. I then noticed the LR was lower than the RR at the wheel opening. There was some body repair done so I remeasured at the body line ( 1/2" lower ). I measured the actual ride height ( frame to diff tube ) and they are equa...	JC2+2	3	609	May 20, 2014 by 4SPEED427
	rusty fenders (Preview) ive got some seriously rusty spots on my 'new' 66 strato chief wagon and wondering if theres any good pieces out there...its the area behind the front wheel wells and all around the rear wheel wells and all the way back to the bumper...thanks	normffff	15	1519	Apr 2, 2014 by 65wagon
	66 Pontiac Stratochief (Preview) Does anybody know where i can get replacement front fender Stratochief emblems or someone who restores them?	Bud Dewson	13	1619	Apr 2, 2014 by normffff
	1967 Parisienne 2+2 front turn signal lenses (Preview) Well, I purchased a set of clear Impala front turn signal lenses, thinking they were the correct ones. They were not, looking further into it...it looks like 1967 Firebird lenses are the same...can anyone confirm this? thanks...	Blackheart4355	19	1648	Mar 29, 2014 by LandShark68_2+2

	Hood latch (Preview) Hey there, my hood is stuck down on my '67 Parisienne, any one know how best to release it? Thanks Ian	Bago	4	623	Mar 10, 2014 by 66 Grande guy
	Metro door weatherstrips (Preview) I installed the Metro door weatherstrips on my GP this afternoon, for obvious reasons as the pic shows (my old pieces, brittle, torn, missing etc). No photo shoot cause it's really a simple job with one exception. What have you guys used to push those retaining pins into the holes in the door??? I used m...	4SPEED427	6	821	Mar 4, 2014 by 65wagon
	1967 Parisienne lower cowl ( 1 2 ) (Preview) Hi, does any one know if the lower cowl panel for a 67 chev Impala will fit my 67 parisienne? They look the same and mine is rusted out and needs repairing. I found this repo one for an impala.	lofty	25	2894	Mar 4, 2014 by BigDogSS
	66 Catalina (Preview) Hi boys I have a chance to buy a complete body with all the parts except motor and frame.Just woundering if its worth my time to buy it and part it out?Its already disasembled. Any comments would be helpful,going to see it tomorrow.It is a sweet deal.	GrtDanes	15	1113	Feb 23, 2014 by Pontiacanada
	No T-3's for this cowboy! ( 1 2 ) (Preview) And I don't mean Tylenol either! We haven't talked about T3's forever, so........ I bought Wagner halogens today for my black GP. I'm not surprised to see that even a company with such a good reputation for quality sells me seal beams that had a boat ride to Canada. Oh well, I guess it's to be expected. An...	4SPEED427	31	2263	Jan 27, 2014 by 65wagon
	Rubber door bumpers still available from GM (Preview) I just thought I'd mention that anyone with a 66 B body (and likely lots of other Pontiacs use the same number) can still buy brand new rubber door bumpers from their local GM dealer. I didn't bring the part number home with me but I got new ones for my car this week. My old ones were either gone or pretty ratt...	4SPEED427	4	660	Jan 22, 2014 by Blackheart4355
	66 Fuel Tank Interchange With Chevrolet? (Preview) There has been some discussion on here in the past regarding fuel tank interchange between 65-66 Canadian Pontiac and 65-66 Chevrolet. My memory says it's never been proven they interchange, and searching old threads on this site, I can't prove it either. So, the million dollar question. Has anyon...	4SPEED427	23	1538	Jan 7, 2014 by 427carl

	66 A/C car question for 66GrandeGuy or Johnny Ringo (Preview) I know one of you two guys can answer my question. I am installing a vacuum reservoir for my power trunk. I pulled two out of my US GP parts car. One is very tiny, about 3" diameter, 4" tall. One is about 7" diameter, 8" tall. I am thinking one of these is for the vacuum trunk, one is for t...	4SPEED427	11	1068	Jan 4, 2014 by 66 Grande guy
	65 Custom Sport vs Grand Prix Grille (Preview) Wondering if a 65 Parisienne Custom Sport grille bezel is the same as a 65 Grand Prix. Might the Grand Prix have an extra mounting hole for the fog light? I only have the Cdn book and took these numbers from it: 9779160 (right) and 9779161 (left ) grille bezel, 5739086 grille radiator Might anyone be able...	norontcan	8	1025	Dec 29, 2013 by norontcan
	Rubber blocks to keep windshield from sliding down (Preview) I may have asked this before but I searched and can't find it, if so. In the not too distant future I need to reinstall the rear glass in my GP. I am going to use urethane and need some of those little rubber blocks to keep the glass from sliding down while the urethane cures. I can't seem to find them. Any idea...	4SPEED427	4	725	Dec 7, 2013 by rabbit64cs
	Metro trunk weatherstrip (Preview) Has anyone used a B body Metro trunk weatherstrip? If so, how is it? I tried mine. It fits the channel very nicely, and it seems to work ok closing the trunk, but the profile sure is a lot different than the original. I had a Soffseal piece years ago on my Acadian and it never let the trunk lid sit down properl...	4SPEED427	4	917	Dec 7, 2013 by beaumontguru
	66 Grande Parisienne Window Fuzzy Installation (Preview) It seems to me that Ken posted up about his experience installing his window seals after his car was painted. I can't find that thread to add my own experience to it, so I'll start another one with apologies if there happens to be some overlap. I also know I posted a link on how to do this, from another forum...	4SPEED427	16	3097	Nov 22, 2013 by 4SPEED427
	1968 2+2 emblem and loovers location (Preview) I am in the process of transforming my 68 Parisienne in a 2+2.The interior is mostly done. I found the loovers of the front fenders and the 2+2 emblems for the rear quarter panel. Does someone have the measurements for the 16 holes securing the loovers and the same for the 2+2 emblem? ( where to punch the...	RogerB	8	861	Nov 6, 2013 by RogerB
«First < 1 … 13 14 15 16 17 … 26 > Last» \| Page of 26 sorted by