|
Are Canadian and American Grand prix parts inter change able
(Preview)
Can Any one tell me if the quarter panels and front fenders are the same on the American Grand Prix as they are on my Grande Parisienne..I'm heading to the states soon and I found a guy with some parts ..obviously I know the American car will have holes in the panels for the chrome strips on the bottom of the...
|
grande jim
|
3
|
1280
|
|
|
|
1969-70 Chrome windshield trims ?
(Preview)
1970 Bonneville convertible chrome windshield trims, the same as 1969 Parisienne convertible ? The pillar ones are L shaped at the top corners.
|
pontorquer
|
3
|
1260
|
|
|
|
Time for re-assembly 67 2+2
(
1 2
)
(Preview)
Got the car back from paint shop.
|
67rag396
|
37
|
3942
|
|
|
|
Locating 65 GP fenders?
(Preview)
I am trying to find some GP fenders, 1965. I looked on the cross canada website and there is nothing listed. Anyone have any suggestions? Thanks for your help in advance.
|
quik4g63
|
6
|
2042
|
|
|
|
70 rag top.
(Preview)
Anybody have any pearls of wisdom about replacing the rag top on a 70 2+2 convertible. I already asked someone and they gave me good info about new side cables, new frame top pads, new tacking strip then they got on about if the curtain is not damged or releasing from the glass then you should be able to use...
|
Stephenzone
|
2
|
1084
|
|
|
|
1967 parisienne parts
(Preview)
hey yall im15 looking to fix my 1967 parisienne it is a rust bucket if ya know what i mean i really dont know where i can get remade parts for my car. Does anyone know who would make parts? oh yea its a 1967 pontiac parisienne 2dr ht 283 v8 with a 2 speed pg trans
|
jonathanD
|
22
|
5016
|
|
|
|
confirm that these 2 + 2 trim are 1970
(Preview)
I was cleaning in the shop ,, stumbled onto these...I belive they are 1970 2 + 2 ?? correct??
|
rabbit64cs
|
4
|
1269
|
|
|
|
|
Interchangable 67 Grande Parisienne valance
(Preview)
I am considering a purchase from The "Tin Man" in BC of a valance from a 67 2+2 that he is parting out. The valance appears to be the same, I have no reason to doubt....well yes I do. Anyone know what years/models used this valance? I appreciate the assistance from CP......its priceless. I ha...
|
Turn2Stone
|
3
|
994
|
|
|
|
67 GP weatherstrip
(Preview)
I am looking for door seals (weatherstrip) for the 67 Grande Parisienne. My intent is not to slam or promote any parts dealer, just to get the right parts. I have orders from Ames and NOS for other things, but am confused. Ames carries these seals for this year, but they state that they can fit all exce...
|
Turn2Stone
|
8
|
1540
|
|
|
|
Rear quarter trim
(Preview)
I am lloking for some options to repair 5 holes drilled in my rear quarter trim. Must have rubbed off an obstacle in the past and the trim was drilled and attatched to body with metal screws. Or possibly there is a place to buy? 90-1/2 " long is the problem. I have shorter pieces but not the one needed....
|
two-door post
|
1
|
1220
|
|
|
|
Hard trim to Find
(Preview)
Here are a couple of pictures for Marty who is looking for these. I found them impossible to get off without twisting off the little diecast nibs that hold them on.
|
66 Grande guy
|
9
|
2073
|
|
|
|
Floor section from behind Rear seat to Trunk
(Preview)
Hi Everyone, Looking for some suggestions. Would like to replace the section of floor from behind the rear seats to the trunk floor for a 67 fullsize Convertible. The section that goes over the differential hump. Looked at sheet metal suppliers like Cross Canada and Impala Bobs and can't seem to f...
|
67 2+2 Ragtop
|
4
|
1782
|
|
|
|
full size pontiac trunk floor and front fenders
(Preview)
Well, I'm back. My friend from the London area just came and picked up my Stratochief to force me into the restoration, so I could use a few parts or some good advice. I was looking at an earlier post where the trunk pan was the subject matter however I didn't notice if anyone has actually measured the o...
|
427strato
|
19
|
3660
|
|
|
|
sheet metal
(Preview)
Hello all i am looking for sheet metal parts for a 1969 ponriac parisienne 2+2 hardtop, does anyone know where i can get it. I am also looking for a front windshield glass. thankyou in advance dymonn2
|
dymonn2
|
2
|
1143
|
|
|
|
|
Trunk lid sizing
(Preview)
Will a trunk lid from a four door 66 Laurentian fit on a two door?width is probably good but length?
|
two-door post
|
9
|
1569
|
|
|
|
Sexy windows
(Preview)
I'm posting this for Marty so he can see the back windows of a 66 Grande Parisienne. Let me know if thisis what you have ok? I need factory tinted too.
|
66 Grande guy
|
16
|
2223
|
|
|
|
65-66 full size pwr antenna install
(Preview)
I just bought an original power antenna assembly from a 66 Parisienne. Does anyone have info on the proper location and wiring, for a 65 or 66? I know it is on the rear but unsure about exact location. Thanks
|
1965CS
|
6
|
1950
|
|
|
|
How to remove front bumper 67 GP
(Preview)
OK, I just got the back bumper off. Disconnected reverse lights, four bolts and its done. I'm not so convinced about the front. The four front bolts are soaking/loosening right now. I'm not sure what part of the housing comes off, and what will stay, its hard to see exactly. Any pointers would be appre...
|
Turn2Stone
|
12
|
1702
|
|
|
|
Opinions on soda blasting?
(Preview)
Hi guys. I am about to start stripping my 65 GP down for restoration.Ive been doing some reading and was wondering what your opinions/experiences with soda blasting paint off cars was.I want the absolute best for this car in this restoration and i know sand blasting is not the way. Any tips or tricks fo...
|
quik4g63
|
5
|
1659
|
|
|
|
Doin it myself
(Preview)
My search for the right body/painter seems futile. I have approached all I can find and not one can do it this winter. I had one offer of "if you can get all prep done to primer, I will paint it for 5k if I have time". I would spend double that if the situation were right, but nobody wants it, and o...
|
Turn2Stone
|
16
|
1946
|
|
|