|
65 beaumont gear ratio
(Preview)
Does anyone know the stock gear ratio for a 65 Beaumont sd
|
Hegedus1000
|
5
|
1036
|
|
|
|
1965 327 300 HP Balancer and pulley set up?
(Preview)
Any ideas or pictures of how it should look? Part numbers? ETC???
|
65sssd
|
7
|
771
|
|
|
|
Coolant on my passenger floor mat. Nationals in 2 days!
(Preview)
OK the 67 Beaumont is off to Moncton for the nationals this week, and wouldnt you know it, i just developed a coolant leak. Windshield fogged up, strong smell, small green puddle on my floor mat. I suspect the heater core has crapped out, and there is no way I can get a new one before I have to leave. The leak...
|
Turn2Stone
|
15
|
1144
|
|
|
|
Convert shifter in 67 beau.
(Preview)
Anyone know how to convert a 2sd console shifter to a 3. Sd th400
|
chader
|
9
|
1026
|
|
|
|
Spark plug!!
(Preview)
Replacing the plugs in an engine that hasn't run much in the last 8 years, and I'm not quite sure what type I should use to replace them with. If anyone knows about this stuff could u help, I can give u specs on engine , just ask me what info u require!
Thanks
Rich
|
Myquik66
|
7
|
1040
|
|
|
|
Raised PONTIAC letter 327 valve covers?
(Preview)
Was their ever and raised PONTIAC letter valve covers with the stagered holes for a small block? If so does anyone have a set for sale?
|
BOSSY
|
4
|
969
|
|
|
|
Mystery 454 Knock
(Preview)
Just tore down my Brother-in-law's 454 from his '69 Beaumont for a knock. Could have swore it was a rod noise. Even got worse as it warmed up. Instead we found two intake cam lobes worn off prematurily (lots of metal suspended in the oil). The crank and bearings still like new. Thinking that since the e...
|
JC2+2
|
17
|
4821
|
|
|
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
|
|
rebuilding my 283
(
1 2
)
(Preview)
I need your help guys , i am pulling out my 283 out of my Beaumont pretty soon actually the engine is bone original and stock , even still have the points in the distributor what i want ............... by the way engine runs fine , its has a leak by the rear crank seal and a...
|
since 1983
|
41
|
4922
|
|
|
|
NEED ADVICE: Flowmaster Super 40 Series Muffler Kit
(Preview)
Help me out here guys... I've got my finger on the trigger to order the 2.5" dual Flowmaster kit for my 396/402. The car currently has Hooker competition headers and a cheap stock dual exhaust system. ...sure sounds good, but I'm think'n it could sound a whole lot better! The Flowmaster kit use...
|
jlysholm
|
19
|
2110
|
|
|
|
Bad Coil?
(Preview)
Well not sure if this is the right place to post this but I couldn't find anywhere else to post this. So car was running amazing two days ago, jumped in it yesterday and no start. Got fuel, she's turning over but not getting any spark. I've got proper volts to the coil so I'm thinking bad coil. I put a meter to...
|
vicfire
|
12
|
1197
|
|
|
|
Heater core bolt areas and pictures of one removed from a 65 Beaumont
(Preview)
I had a member ask me about the steps to remove a heater core so I hope these pictures help. You remove the bolts on the firewall and the heater box inside the car will drop into the car. One of the nuts is behind the inner fender but a boxed rachet end wrench will get that. I put a blanket on top for the motor and...
|
65sssd
|
1
|
828
|
|
|
|
Hood clearence on a 67 beau
(Preview)
Hey, anyone have trouble fitting an edelbrock rpm air gap+Q-jet under the hood?
|
Captain Beaumont
|
2
|
797
|
|
|
|
454 bbc - header install - clearance question
(Preview)
I've hired help from the guy who did my Flowmaster setup to install my new headers. They appear to offer a little more clearance than the old cast iron, but its too close to call for me. He is a perfectionist and did a fantastic job with the exhaust. I know that I should have done the headers at the same time,...
|
Turn2Stone
|
4
|
2062
|
|
|
|
Lakepipes of today
(Preview)
Check out quicktimesperformance.com for some cool electric cutouts. No taking the caps off de ol lakepipes no more ! We installed these on my sons camino this weekend.
|
Elroy
|
13
|
1436
|
|
|
Nov 18 to Dec 2 Black Friday UP TO 50% OFF Plus Huge Coupons
|
|
Big block cylinder heads
(Preview)
What is a good cylinder head to use on my .030 over 396 ? The engine came out of a 1968 Pontiac 2+2 ( 396 2 bbl ) so I think the heads might be wrong with my cam and Q-jet. I checked out the casting numbers and its 3933148, I would like a little more punch from my rat and wondering if heads with a bit bigger valv...
|
69SD
|
20
|
3293
|
|
|
|
Looking for some 65 beaumont 4 spd flywheel advise!
(Preview)
I have been putting together a collection of parts for my 65 327 4 spd SD and I noticed some cracks in the face of the flywheel I was sold that was supposed to be for a 327. I don't want to use it now but I have another and when I measured it I was confused. I was wondering if anybody knows the dimension of the orin...
|
65sssd
|
23
|
1648
|
|
|
|
3721 Carter carb part number questions
(Preview)
Does anybody know how to read the date on these carbs and what does the SA. SB, or just a S after the 3721 mean? Does anybody have one for sale? I am also looking for a good 1111075 distributor.
|
65sssd
|
18
|
3217
|
|
|
|
intake maifold and carb
(Preview)
Anybody know the numbers for a 68 beaumont intake manifold for 396 325hp and is it different that the 350 hp ? Or the numbers for the proper carb ? Thx Jason
|
JJ
|
6
|
1227
|
|
|
|
What size is the casting number on your Canadian 327 300hp or 250hp Block?
(
1 2 3
)
(Preview)
I'm looking for some guys eg. (70 Acadian SS) and others that have tech info that have a 65 Beaumont with a numbers matching motor or think they have a numbers matching Block to have a look. The question I have is would a 300hp 327 65 Beaumont have a 3782870 or other casting number with the American size cas...
|
65sssd
|
51
|
5269
|
|
|
|
"Beaumont 396" Air Cleaner Sticker
(Preview)
Has anybody purchased repro 1967 "396 Beaumont" air cleaner sticker from Perogie Enterprises? http://www.perogie.com/pontiacother.htm I own a '67 L-34, and would like to find a NOS open air cleaner assembly and correct stickers. There are currently stickers selling on Eba...
|
jlysholm
|
6
|
3743
|
|
|